B&K CT610, CT600, CT602, CT310, CT300 user manual Installation and System Diagrams

Page 13

	9
Installation and System Diagrams

Installation and System Diagrams

Zone D	Zone C	Zone B	Zone A

Zone E

Keypads

Sources

Zone F

CT602

Zone Speaker

Connections

Zone F Zone E	Zone D	Zone C	Zone B Zone A
		See the following pages for details describing
	B & K	See the following pages for details describing
	B & K	installation procedures.

S I M P LY B E T T E R !

Image 13

Contents 13226 Accessories Included Installation and System Diagrams Parts and Accessories GuideSetup Using a PC and BKcSuite BKcSuite Setup and OverviewOn Screen Main Menu SpecificationsIntroduction / Overview Finesse and Power To Please a HouseholdCT Receiver Features and Benefits Point Any Remote Control at the Keypad CK1.2 Keypad Features and BenefitsCK1.2 Keypad Features and Benefits Status Feedback to KeypadsCT Receiver Front Panel CT602/600/300 Parts and Accessories GuideS E CT Receiver Back PanelProgramming Jack Behind the Faceplate CK1.2 Front Panel / Back PanelMZ-128 Remote Control RJ-45 to 5 position Phoenix Adapter P/N CT-1 System Integrator P/NDB-9 to RJ-45 Adapter P/N13290 BK Toolbox CD-ROM P/NInstallation and System Diagrams Installation and System DiagramsBasic System Hookup Default Operation Placement and VentilationInstallation Considerations Connection StrategyAccommodate up to 12-gauge wire AC Power and Line FuseSpeaker Connections for CT Receiver Speaker Connections CT310CT Receiver Speaker Connections Example CT Receiver Six Zone Speaker ConnectionsExample connection of a CK1.2 Keypad Keypad ConnectionsCommon Ground CK1.2 Keypad ConnectionsCT Receiver cannot receive RS-232 via this terminal Left Control Card Adding Additional Keypads in the Same ZoneCT Receiver Connection Shared Source ConnectionsBuffered Outputs IR Flasher Emitter OutputIR Emitter Outputs Zone Line Outputs Zone Line OutputsDedicated Source Inputs Local Changing Line Level Outputs From Fixed to VariableFixed Output / Variable Output Local Source IR Control Local IR Source ControlCT Receiver Common Control Connection and Trigger Common Control TriggersCommon Control Triggers RF Remote Factory ResetAM Loop Antenna FM AntennaSystem Expansion System ExpansionCoupling Two CT Receivers Maximum 12 Stereo Zones Connecting Two CT ReceiversSwap Cable Between Two CT Receivers Should not be connected between RJ- 45 jacksSeventh Zone Connection Diagram No identical Adding a 7th Zone Using The AVR507/505/50 Second ZoneAdding a 7th Zone SourcesCT-1 IR Routing System Integrator Swap Cable ConstructionCAT5 T568B Swap Cable RS-232 Swap CableCT610 #3 CT610 #2 Basic Expanded System Using a CT-1CT-1 Power Connection 12VDC Source Control Using a CT-1CT-1 Expansion RS-232 Connection Adding a Home TheaterUsing a Swap Cable to Control a Theater Setup Using a PC and BKcSuite Setup Using a PC and BKcSuiteCT Receiver Connection Connection to a PCComputer Connection USB to Serial AdapterBKcSuite Setup and Overview BKcSuite Setup and OverviewBKcSuite Task Bar Explained BKcSuite Task Bar ExplainedBasic Setup Menu Basic Setup MenuAdvanced Setup Menu Advanced Full Setup MenuHardware Zone Settings Tab Maximum Level Limits the Output whether Fixed or Variable Fixed or Variable Levels for Stereo ZonesLeft and Right Level Calibration Fixed or Variable Levels for Mono ZonesSub-Zoning Splitting a Zone To MonoCode-Set Description and Overview Code-Set Description and OverviewGroups / Code Sets / Zones Tab M P LY B E T T E R Input Settings Tab Input Settings To Compensate LevelsShared Source Input Names Dedicated Source Input NamesPower On Titles Tab Power On Preference Select Power On SettingPower-On Preferences Tab Select Code SetSelection Mode Input ModeInput Configuration Tab Release TimeActivated By Action/ Event Tab Event LevelIndividual Zone Display Front Panel BrightnessDisplay Tab Zone Control Out Zone ControlHeadphone 12V Control TabIR Flasher Settings Tab Zone Rear Data In SettingFlasher Outputs Front Panel IR to Flasher OutputsFront Panel Buttons Setup Menu VisibleFront Panel IR Memory LockedRS-232 Echo Enabled RS-232 Port EnableBaud Rate RS-232 Receive & Transmit IDRS-232 Feedback Selection Continuous Reply V2.0 EnabledConvert IR to BKC-DIP Messages Transmit BKC-DIP to ZonesFavorite Preset Recall Recall Volume In PresetPreset Operation Tab Auto NamingKeypad Feedback Tab Opening the Preset Editor Preset Editor Features and BenefitsPreset Editor Editing Presets Preset Editor WindowRS-232 Serial Macro Editor RS-232 Serial Macro EditorCK1.2 Keypad CK1.2 KeypadSetup Using the On Screen Display Setup Using the On Screen DisplayCT Receiver On Screen Display Menu Structure OSD On Screen Menu Tree DiagramUsing The Remote Control and On-Screen Menus Using a Remote ControlOn Screen Menu Operation with the MZ-128 CT602 / CT300 No front panel operation CT610 / CT310Front Panel Buttons On Screen Main Menu Main MenuZone Operation Zone Favorite Presets MenuInputs Sub-Menu Audio/Video System SetupNaming an Input Main Menu Sub-menu’sMenu Items for a Dedicated Input Zone Menu when set to MonoAudio / Video Submenu Page/Event Setup Zone Power On SettingsDisplay Setup Control Menu SetupZone Code-Sets/Names and Group Titles Control System MenuCode Set Zone Code-Sets/Groups and Group TitlesFlasher Out Common Control I/OIR Routing for Identical Components Flasher OutputIR to Flasher Out Power On Titles Presets SetupPreset Volume Preset NamesSecurity Options Control System SetupRS-232 Options Setup RS-232 Slave Control Memory BackupSystem Status Main Menu SetupZone Planning Worksheets # of Volume ControlsCable Calculation Source Distance for Home Run Total CT Receiver Input PlanningInput Planning Worksheet Power On Preferences and Presets CT Receiver Preferences and PresetsProject Manager Date Troubleshooting Guide for CT Receivers Troubleshooting Guide For BKcSuiteProblem Possible Solution Returning Equipment Limited WarrantyCT610/602 CT600 CT310 CT300 Specifications