B&K CT602, CT600, CT310, CT610, CT300 user manual Setup Using the On Screen Display

Page 66

62

Setup Using the On Screen Display

 

Setup Using the On Screen Display

 

 

MAIN MENU

 

 

 

 

1

Zone Operation

 

 

 

2

Zone Favorite

Presets

 

 

3

Audio/Video

System

Setup

 

4

Control System Setup

 

 

5

Memory Backup/Restore

 

 

6

System Status

 

 

 

 

↑↓ next item

 

SEL select

 

 

MENU exit menu system

 

 

 

 

 

 

It is possible to completely program the CT Receiver via the on-screen menus or the front panel dis- play. However, it is not nearly as fast and straightforward as using a PC and BKcSuite. Nevertheless, it is often convenient to touch up one or two parameters of the system using the on-screen or front panel menus. Please note that the CT602/300 does not have front panel buttons or a display. All on screen setup on a CT602/300 must be done through the zone A video output run to a monitor accessed by remote control. Remote control access to the on screen menu is limited to zone A only.

The on screen menu cannot be accessed by any zone other than zone A.

B & K

S I M P LY B E T T E R !

Page 65 Page 67
Image 66
Page 65 Page 67
Contents 13226 Accessories Included Setup Using a PC and BKcSuite Parts and Accessories GuideInstallation and System Diagrams BKcSuite Setup and OverviewSpecifications On Screen Main MenuFinesse and Power To Please a Household Introduction / OverviewCT Receiver Features and Benefits CK1.2 Keypad Features and Benefits CK1.2 Keypad Features and BenefitsPoint Any Remote Control at the Keypad Status Feedback to KeypadsParts and Accessories Guide CT Receiver Front Panel CT602/600/300CT Receiver Back Panel S ECK1.2 Front Panel / Back Panel Programming Jack Behind the FaceplateMZ-128 Remote Control DB-9 to RJ-45 Adapter P/N13290 CT-1 System Integrator P/NRJ-45 to 5 position Phoenix Adapter P/N BK Toolbox CD-ROM P/NInstallation and System Diagrams Installation and System DiagramsBasic System Hookup Installation Considerations Placement and VentilationDefault Operation Connection StrategySpeaker Connections for CT Receiver AC Power and Line FuseAccommodate up to 12-gauge wire Speaker Connections CT310Example CT Receiver Six Zone Speaker Connections CT Receiver Speaker ConnectionsKeypad Connections Example connection of a CK1.2 KeypadCK1.2 Keypad Connections Common GroundCT Receiver cannot receive RS-232 via this terminal Adding Additional Keypads in the Same Zone Left Control CardShared Source Connections CT Receiver ConnectionIR Flasher Emitter Output Buffered OutputsIR Emitter Outputs Zone Line Outputs Zone Line OutputsChanging Line Level Outputs From Fixed to Variable Dedicated Source Inputs LocalFixed Output / Variable Output Local IR Source Control Local Source IR ControlCommon Control Triggers CT Receiver Common Control Connection and TriggerCommon Control Triggers AM Loop Antenna Factory ResetRF Remote FM AntennaSystem Expansion System ExpansionSwap Cable Between Two CT Receivers Connecting Two CT ReceiversCoupling Two CT Receivers Maximum 12 Stereo Zones Should not be connected between RJ- 45 jacksAdding a 7th Zone Adding a 7th Zone Using The AVR507/505/50 Second ZoneSeventh Zone Connection Diagram No identical SourcesCAT5 T568B Swap Cable Swap Cable ConstructionCT-1 IR Routing System Integrator RS-232 Swap CableBasic Expanded System Using a CT-1 CT610 #3 CT610 #2Source Control Using a CT-1 CT-1 Power Connection 12VDCCT-1 Expansion Adding a Home Theater RS-232 ConnectionUsing a Swap Cable to Control a Theater Setup Using a PC and BKcSuite Setup Using a PC and BKcSuiteComputer Connection Connection to a PCCT Receiver Connection USB to Serial AdapterBKcSuite Setup and Overview BKcSuite Setup and OverviewBKcSuite Task Bar Explained BKcSuite Task Bar ExplainedBasic Setup Menu Basic Setup MenuAdvanced Full Setup Menu Advanced Setup MenuHardware Zone Settings Tab Left and Right Level Calibration Fixed or Variable Levels for Stereo ZonesMaximum Level Limits the Output whether Fixed or Variable Fixed or Variable Levels for Mono ZonesSplitting a Zone To Mono Sub-ZoningCode-Set Description and Overview Code-Set Description and OverviewGroups / Code Sets / Zones Tab M P LY B E T T E R Shared Source Input Names Input Settings To Compensate LevelsInput Settings Tab Dedicated Source Input NamesPower On Titles Tab Power-On Preferences Tab Select Power On SettingPower On Preference Select Code SetInput Configuration Tab Input ModeSelection Mode Release TimeAction Activated By/ Event Tab Level EventFront Panel Brightness Individual Zone DisplayDisplay Tab Headphone Zone ControlZone Control Out 12V Control TabFlasher Outputs Zone Rear Data In SettingIR Flasher Settings Tab Front Panel IR to Flasher OutputsFront Panel IR Setup Menu VisibleFront Panel Buttons Memory LockedBaud Rate RS-232 Port EnableRS-232 Echo Enabled RS-232 Receive & Transmit IDConvert IR to BKC-DIP Messages V2.0 EnabledRS-232 Feedback Selection Continuous Reply Transmit BKC-DIP to ZonesPreset Operation Tab Recall Volume In PresetFavorite Preset Recall Auto NamingKeypad Feedback Tab Preset Editor Features and Benefits Opening the Preset EditorPreset Editor Preset Editor Window Editing PresetsRS-232 Serial Macro Editor RS-232 Serial Macro EditorCK1.2 Keypad CK1.2 KeypadSetup Using the On Screen Display Setup Using the On Screen DisplayOn Screen Menu Tree Diagram CT Receiver On Screen Display Menu Structure OSDUsing a Remote Control Using The Remote Control and On-Screen MenusOn Screen Menu Operation with the MZ-128 CT610 / CT310 CT602 / CT300 No front panel operationFront Panel Buttons Main Menu On Screen Main MenuZone Favorite Presets Menu Zone OperationNaming an Input Audio/Video System SetupInputs Sub-Menu Main Menu Sub-menu’sZone Menu when set to Mono Menu Items for a Dedicated InputAudio / Video Submenu Zone Power On Settings Page/Event SetupZone Code-Sets/Names and Group Titles Control Menu SetupDisplay Setup Control System MenuZone Code-Sets/Groups and Group Titles Code SetIR Routing for Identical Components Common Control I/OFlasher Out Flasher OutputIR to Flasher Out Preset Volume Presets SetupPower On Titles Preset NamesControl System Setup Security OptionsRS-232 Options Memory Backup Setup RS-232 Slave ControlMain Menu Setup System Status# of Volume Controls Zone Planning WorksheetsCT Receiver Input Planning Cable Calculation Source Distance for Home Run TotalInput Planning Worksheet CT Receiver Preferences and Presets Power On Preferences and PresetsProject Manager Date Troubleshooting Guide For BKcSuite Troubleshooting Guide for CT ReceiversProblem Possible Solution Limited Warranty Returning EquipmentSpecifications CT610/602 CT600 CT310 CT300
Top Page Image Contents