Polaroid SX70 manual Film Processing Components, Sequence of Operations

Page 27

G. FILM PROCESSING COMPONENTS

The basic theory of the film processing method remains unchanged from previous Polaroid system. That is , the developping chemistry is encapsuled in a pod on each sheet of film and, as the sheet is passed between rollers, the pod is burst and the chemical spread evenly between the negative and the mylar protective cover. Except for this characteristics, no direct similarities exist. The SX-70 camera employs a unique process which totally eliminates the «throw array» negative. The print is drawn through the spread rolls by the motor drive system so that no action need be taken by the operator. See Figure2-10. Development takes place outside of the camera and unaffected by ambient light conditions. Since the end result is determined when the picture emerges from the camera, no time measurement si necessary. (Additional film information is available on page 60 and 61 of «The world of SX-70»)

Figure 2-10 Spread roller system

H. SEQUENCE OF OPERATIONS

The operator pushes S1, applying full power to solenoid #1, which closes the shutter blades, and pushed solenoid #1 against S4, changing it from CA to CB. Closing CB cuts solenoid #1’s power from high to low; low is enough to hold the blades closed. Closing CB also signals the ECM to start the motor. The motor starts the gear train moving. The movement of a cam on cam on the gear train releases the recock ram and, through

spring action, raises the Fresnel carrier. When the recock rammoves, it opens S5 and then S3 at certain Fresnel carrier angles. Opening S5 stops the motor after it has made only a brief jog. Opening S3 starts the «Y» delay : 40 milliseconds delay which allows the Fresnel carrier to come to rest after its travel. (This eliminates bouncing caused by the sudden stop of the carrier on the mirror cover.)

At the end of the «Y» delay, power is removed from solenoid #1, allowing the spring to open the shutter for exposure, and moving S4 from CB to CA position. When the proper exposure level is reached, the photocell trips the Schmitt Trigger (S/T) in the ECM which sends full power to solenoid #1. This closes the blades and tranfers S4 from CA to CB. As before, closing CB cuts solenoid #1’s power from full to low, sufficient to hold the blades closed; closing CB also signals the electronics to start the motor.

The motor starts the gear train again, and this time the cams cause a series of actions at different position of gear train movement :

-it starts the pick which pulls the film into the rollers (one of which is attached to gear train it is this powered roller rotation that pulls the film through and out of the camera);

-it stops the pick;

-it pulls down the Fresnel carrier, which in turn, moves the counter to the next number;

-it moves the recock ram, closing S3 (resetting it for the next cycle);

-it retruns the pick;

-it seats the Fresnel carrier so it is ready for the next cycle;

-it moves the recock ram, closing S5, which stops the motor;

-and it stops the spred action.

When S5 closes, it cuts power to the solenoid #1; the spring opens the shutter blades, and S4 is pushed from CB to CA. (The blades open only if the operator releases the red button.) The system is ready for a new exposure cycle.

Springs are used in three of the operations discussed above : holds the shutter blades open, filps the Fresnel carrier up, and holds the pick at the rest position.

As indicated, inserting a film pack causes automatic action. This could, of course, be a

Image 27
Contents Page Page General Description DescriptionOpening the Camera Camera OperationStarting the Automatic Mechanism Loading the Film packViewing and focusing Setting the exposure counterViewing and shooting Exposures using flash Completing the film packDeveloping the print Closing the camera Shutter Description Ambient Light Mode11 a Location & Arrangement of internal parts Shutter Description Flash Mode Page 14 S5 being opened by the recock ram Gear train Page Viewing and Exposing System Power SourceIntroduction LensViewfinder optics exposing Fresnel Figures 2-3 a and 2-3 BFresnel screen Camera Elctronics 1. General ViewfinderMirrors Flare baffleSX-70 Switch locations Switch functionsS3 Being opened by recock ram S4 Switch operating configurations Function Sequence Switch Function TablePage Flash Timing Sequence Chart Shutter, exploded view Shutter Mechanical Details FigureA Solenoid S2 operation Sequence of Operations Film Processing ComponentsPage Max Introduction Initial Tests III TroubleshootingSX-70 Cmaera Repair Inspection Procedure Test Equipment Operation Power supply and pack simulator FigureLocation of new collimator target Collimator FigureDisengaging the idler gear Comprehensive tester Comprehensive Testers -6Model B Camera tester Model B Camera Tester Light Leak Tester Figure Comparalumen Light Levels TableLight leak test system Flash Simulator Board Figure10 Manual camera tester Manual Function Tester FigureManual Function Test Sequence Exit Pupil Test Optical System13 Aligning the exit pupil gage Entrance Pupil TestCollimation USE of Analysis ChartsConcave Mirror Distortion Check Fresnel Quality Check16 Fresnel standards chart 18 Flex circuit terminal locations Camera/Shutter Isolation19 Test points on SX-70 shutters Camera Analysis ChartsPage Front COVER/SPREAD Roll Assembly InstallationRemoval Front cover hinge studs Repairs / Adjsutments Loose Front CoversBending the stop latch Interference Between Front and Bottom Covers Top Spread Roll LoosenessReplacing the Light Shield Cam Front cover light shield cam Mirror Cover / Boot AssemblyBoot retaining screws