Polaroid SX70 manual Concave Mirror Distortion Check, Fresnel Quality Check, Collimation

Page 44

3.Concave Mirror Distortion Check

a.Focus on a target which presents a clear vertical line (for example a door frame).

b.Scan the camera horizontally.

c.If the mirror is not distorted, the vertical line seen in the eyepiece will vary at the camera is scanned. At either side of the field, the line will be bent while in the center of the field, the line will be straight (see Figure 3-15 A).

d.If the mirror is distorted, the vertical lines change more graphically as the image si scanned and one or several reversals of direction of bending may occur (Figure 3-15 B).

e.A telephone directory page at a distance of

2 feet may be used to check distortion. The white pages have high contrast, fine detail and uniform printing.

f.The frame around the viewfinder may appear non-sysmmetrical about the vertical axis. A normal mirror will appear to be sysmmetrical about the axis (Figure 3-15 C).

Figure 3-15 Identifying distorted mirrors

4. Fresnel Quality Check

The Fresnel screen must be examined for blemishes, shadows, dirt, scratches, etc. A standards chart (Figure 3-16) is available for determining whether the Fresnel being examined is acceptable. Focus the camera to 10.4’’for viewing the chart.

a. First, view the Fresnel against the background presented in Section I of the chart. Note whether the defects (dirt, scratches, digs, etc.) are in the A or B aera of the Fresnel.

b. Nest, compare any boot or mirror marks on the Fresnel with the marks shown in Section II of the chart. If the mark exceeds that shown on the chart, the Fresnel is not acceptable.

c. View the Frenel screen against the background of Section III on the chart. The conditions shown on the chart are the maximum acceptable limits for Fresnel defects. If the Fresnel being examined has defects which go beyond those shown on the chart, reject the Fresnel. (Note that an illustrated listing on the chart is available for comparison to Fresnel which have only one or two blemishes.

d. Examine any shading on the Fresnel against the limits shown in Section IV of the chart. If the shading extends beyond the aera (top or bottom of the Fresnel) shown on the chart, the Fresnel si not acceptable.

e. Examine teh split image circle by comparong it against teh examples shown on the chart. If the shading on the split is greater than shown or if there is more than one dig, pit, stain, or scratch on the split, the Fresnel is not acceptable. the Fresnel must also be rejected if the blemish on the split is larger than any shown on the chart.

5. Collimation

For the collimation procedure, refer to paragraph D «Test Equipment Operation».

E. USE OF ANALYSIS CHARTS

The following charts should be used to identify and correct faulty camera operation. It will seldom be necessary to consult every chart. Only those related to a particular malfunction should be consulted. In some cases, the customer’s complaint will be sufficiently specific to lead you to a particular chart. In other cases, the preliminary inspection procedure at the beginning of this section will provide usefull information to lead

Image 44
Contents Page Page Description General DescriptionCamera Operation Opening the CameraLoading the Film pack Starting the Automatic MechanismSetting the exposure counter Viewing and focusingViewing and shooting Developing the print Exposures using flashCompleting the film pack Shutter Description Ambient Light Mode Closing the camera11 a Location & Arrangement of internal parts Shutter Description Flash Mode Page 14 S5 being opened by the recock ram Gear train Page Power Source IntroductionLens Viewing and Exposing SystemFresnel Figures 2-3 a and 2-3 B Viewfinder optics exposingFresnel screen Viewfinder MirrorsFlare baffle Camera Elctronics 1. GeneralSwitch functions SX-70 Switch locationsS3 Being opened by recock ram S4 Switch operating configurations Switch Function Table Function SequencePage Flash Timing Sequence Chart Shutter Mechanical Details Figure Shutter, exploded viewA Solenoid S2 operation Film Processing Components Sequence of OperationsPage Max III Troubleshooting Introduction Initial TestsSX-70 Cmaera Repair Inspection Procedure Power supply and pack simulator Figure Test Equipment OperationCollimator Figure Location of new collimator targetDisengaging the idler gear Comprehensive Testers -6 Comprehensive testerModel B Camera tester Model B Camera Tester Comparalumen Light Levels Table Light Leak Tester FigureFlash Simulator Board Figure Light leak test systemManual Function Tester Figure 10 Manual camera testerManual Function Test Sequence Optical System Exit Pupil TestEntrance Pupil Test 13 Aligning the exit pupil gageUSE of Analysis Charts Concave Mirror Distortion CheckFresnel Quality Check Collimation16 Fresnel standards chart Camera/Shutter Isolation 18 Flex circuit terminal locationsCamera Analysis Charts 19 Test points on SX-70 shuttersPage Removal Front COVER/SPREAD Roll AssemblyInstallation Repairs / Adjsutments Loose Front Covers Front cover hinge studsBending the stop latch Replacing the Light Shield Cam Interference Between Front and Bottom CoversTop Spread Roll Looseness Mirror Cover / Boot Assembly Front cover light shield camBoot retaining screws