Axis Communications 223M user manual Unit Connectors, Terminal connector

Page 51

AXIS 223M - Unit Connectors 51

Unit Connectors

This section describes the following:

•The I/O Terminal connector

•Power connections

•The RS-232 D-Sub Connector

I/O Terminal connector

The 10-pin I/O terminal connector provides the interface to a solid state relay output, two digital photo-coupled inputs, RS-485, GND and auxiliary power.

The terminal connector is used in applications for e.g. motion detection, event triggering, time lapse recording, alarm notification via e-mail, image storage to FTP locations, etc.

•Input - Used for connecting external alarm devices and triggering images for spe- cific alarm-based events. The input is typically connected to a motion detector or any other external security device, and images can be uploaded whenever the detector is activated. Maximum 18V DC is allowed on the input.

•Output - This can drive a maximum load of 50V DC at 100mA directly or heavier loads by connecting additional relay circuitry. If the output is used with an exter- nal relay, a diode must be connected in parallel with the load for protection against any voltage transients.

Caution!

Connecting AC to the inputs/outputs will damage the unit.

10-pin I/O Terminal connector (including RS-485)

Reset/Control	Audio out
Button

Audio in

Network connector

Power connector block

	RS-232 connector	Power adapter	Connect AC power (10-24V) on pins 2 and 3.
			Connect DC power (7-24V) on pins 1 and 2.
		connector

Image 51

Contents Axis 223M Network Camera User’s Manual About this Document Contents Axis 223M Product Features Overview LED Access from a browser Accessing the CameraSetting the root password Accessing the camera from the InternetSetting the focus Layout Live ViewAMC Audio controls Video Streams Video stream typesMotion Jpeg MPEG-4 protocols and communication methods How to stream MPEG-4Other methods of accessing the video stream Axis Media ControlRTP/RTSP/HTTP or RTP/RTSP/HTTPS Other MPEG-4 clients Accessing the setup tools from a browser Setup ToolsVideo and Image Settings Image settingsImage appearance Text overlay settings Video streamTest Overlay/Mask settings Overlay/Mask typeUpload and use an overlay/mask Advanced settings Camera SettingsOverlay image requirements MPEG-4 Settings Mjpeg Settings Audio Settings Enable Audio Audio Channels Audio modeAudio Audio Input Audio Output Use custom settings Live View ConfigOwn Home Upload Own Web FilesExample Check Show custom Link User Defined LinksAction Buttons Output ButtonsHtml Examples Default Video FormatDefault Viewer Viewer SettingsExternal Video Sequence ModeEvent Configuration Event ServersDefinitions Click Add triggered... on the Event Types Configuring Event TypesHow to set up a triggered event Triggered eventScheduled Event Pre-trigger and Post-trigger buffersCamera Tampering SettingsMotion Detection Object size, history and sensitivity Port StatusReferrals System OptionsSecurity Users Security IP Address FilteringSecurity Https Security CA servers Authentication processNetwork Basic TCP/IP Settings IP Address ConfigurationDate & Time NTP Configuration Network Advanced TCP/IP SettingsServices DNS ConfigurationHost Name Configuration Link-Local IPv4 AddressNAT Traversal Network Traffic Network SocksNetwork QoS Quality of Service QoS SettingsNetwork Smtp email Network Bonjour Network SnmpNetwork UPnP Network RTP Multicast/MPEG-4Support Overview LED SettingsMaintenance SupportLogs & Reports AdvancedAbout Using the Control Button Resetting to the factory default settingsTerminal connector Unit ConnectorsTerminal connector schematic diagram Terminal connector pinout tablePower connections Power connector blockSchematic diagram Power terminal block and Power connectors RS-232 connector Upgrading the firmware TroubleshootingBasic Configuration Checking the firmwareAxis support Emergency recovery procedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsVideo/Image problems general Status and Network indicator LEDs are flashing red rapidly Removing and attaching the lens Replacing the lensLens Technical SpecificationsUsers System integration Optimizing your system General performance considerationsBandwidth Frame rates Motion Jpeg and MPEG-4Axis 223M Technical Specifications Glossary of Terms Axis 223M Glossary of Terms Axis 223M Index IndexRtsp