Vivotek 4X-IP7142 manual

Page 42

VIVOTEK - A Leading Provider of Multimedia Communication Solutions

Exposure level:

You can manually set up the Exposure level, which ranges from 1 to 8. The default value is 4.

AGC (Auto Gain Control):

You can manually set up the AGC level (2X, 4X, or 8X). The default value is 4X.

Enable auto iris:

Select it to enable the auto iris function.

Enable WDR (Wide Dynamic Range):

Select it to enable the WDR function. This Network Camera with WDR feature can cope with very challenging lighting conditions. It is capable of capturing both of the dark part and bright part of a target and combining the differences into a scene to generate a highly realistic image as the human eyes can see. Note that if you select this function, Exposure level and AGC function will be disabled.

Switch to B/W in night mode:

Select it to enable the Network Camera to automatically switch to B/W in night mode.

IR cut filter:

With a removable IR-cut filter and built-in IR illuminators, up to 15m, this Network Camera can automatically remove the filter and turn on the IR illuminators during the nighttime to accept IR illumination for low light sensitivity.

■ Auto

The Network Camera automatically removes the filter by judging the level of ambient light.

■ Schedule mode

The Network Camera switches between day mode and night mode based on specified schedule. Enter the starting time and ending time for the day mode. Note that the time format is [hh:mm] and is expressed in 24-hour clock time. By default, the starting time and ending time of day mode are set to 07:00 and 18:00.

■ Day mode

In day mode, the Network Camera switches on the IR cut filter at all times to block the infrared light from reaching the sensor so that the colors will not be distorted.

■ Night mode

In night mode, the Network Camera switches off (remove) the IR cut filter to allow the infrared light to pass through. This improves the sensitivity of the Network Camera in low-light conditions.

You can click Preview to fine-tune the image, or click Restore to recall the original settings without incorporating the changes. When completed with the settings on this page, click Save to take effect and click Close to quit the page.

Video quality settings for stream 1 / stream 2: You can set up two seperate streams for the Network Camera for different viewing devices. For example, set the Network Camera to a smaller frame size and a lower bit rate for remote viewing on mobile phones. Or, set the Network Camera to a larger video size and a higher bit rate for live viewing on web browsers.

■ Mode

The Network Camera offers two choices of video compression standards for real-time viewing: MPEG-4 and MJPEG.

42 - User's Manual

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Page Table of Contents Package contents Read before useConnectors Physical descriptionDI/DO Diagram Hardware installation Hardware ResetWall mount Ceiling mount Ethernet switch Network deploymentInternet connection with static IP Set up the Network Camera through Power over Ethernet PoE Software installation 0002D17142ADAccessing the Network Camera Using web browsersPage Using Rtsp players Using 3GPP-compatible mobile devices MPEG-4Using Vivotek recording software Main Live Video Window Video title Title and time Client Settings MP4 Saving Options System SystemSystem Time DI and do Add User Root PasswordSecurity Manage UserEnable Https Create and Install CertificateTo create a self-signed certificate Certificate Information Network Network TypePPPoE Point-to-point over Ethernet Page Http Https Two way audioFTP Rtsp Streaming Page Ddns Dynamic domain name service DdnsCustomSafe100 Access list Allowed list / Denied listDelete allowed list / Delete denied list Video settings Audio and videoImage Settings Privacy mask Page Page Audio settings To enable motion detection, follow the steps below Motion detectionPercentage = 30% RS485 Settings Camera controlPreset Position Custom CommandNetwork Camera Media Settings ApplicationSnapshot20080104100341 Server Settings Page Page Event Settings Page Recording Settings RecordingPage System log Remote LogCurrent Log View parameters Maintenance RebootRestore Upload / Export Daylight Saving Time Configuration File Upgrade Firmware Page URL Commands of the Network Camera OverviewStyle convention Get server parameter values General CGI URL syntax and parametersSecurity level Method GET/POSTSet server parameter values Page Available parameters on the server Timezoneindex 489 ~ Group dii0~ndi-1 Group doi0~ndo-1Group security Subgroup of network httpSubgroup of network https Subgroup of network rtspSubgroup of network pppoe Group ipfilter Page Page Adjust saturation of image according to mode settings Group upnppresentation Group upnpportforwarding= Logalert = Logcrit Even Group uarti0~n-1 n is uart port countGroup capability Group eventi0~2 Group serveri0~4 Group mediai0~4 Group recordingi0~1To enable or disable this recoding Drive the digital output Query status of the digital inputQuery status of the digital output Capture single snapshotAccount management System Information Upgrade firmwareSystem logs Method PostIP filtering Method GET/POSTGet SDP of Streamings Open the network streamingsSenddata Page Technical Specifications LensTechnology License Notice Electromagnetic Compatibility EMC
Top Page Image Contents