Edimax Technology PT-111E, MD-111E Federal Communication Commission Interference Statement

Page 51

Network Camera User’s Manual

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal operation.

Federal Communications Commission (FCC) RF Exposure Requirements

SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

51/59

Page 50 Page 52
Image 51
Page 50 Page 52
Contents PT-111E / PT-112E & MD-111E Table of Contents Minimum System Requirement OverviewPackage Contents Internal Microphone Light sensor Lens Wired cover Slide coverReset button Micro SD/SDHC ConnectionsHardware Installation Power over Ethernet PoE  Using a PoE-enabled switch Locate the IP address of Network IP Camera Connect to the Network CameraNetwork Camera User’s Manual Initial Access to the Network Camera Video will be displayed Primary user’s capability Configuration functionsView capabilities Camera viewPan/Tilt & connection control buttons PT-111E / PT-112E only Client Setting 16/59 System parameters Definitions in ConfigurationGeneral Setting Host name LED indicatorCurrent Time Time Setting Time zoneAdjust by NTP server Daylight savingSecurity setting SecurityManage user 20/59 LAN Network SettingNetwork LAN & PPPoEDdns Setting Get IP address automatically Use fixed IP addressPPPoE 23/59 Access list setting Access listGeneral Setting Audio and Video settingVideo Setting Infrared Led SettingAudio Setting Schedule mode Video recordSchedule information 1NAS Record parametersBit rate Audio codec settingVideo codec setting StreamSnapshot and time display setting Camera control Camera control PT-111E / PT-112E onlyPatrol list setting Sun/Mon/Tue/Wed/Thu/Fri/Sat Select the days ApplicationResponse mode Trigger modeMedia mode Snapshot & Record file setting4NAS Storage Status NAS server settingFile operation Syslog Status and Parameters Maintenance Export/Import file Appendix Q1 Status led does not light upQ2 What kind of Ethernet cable is used by network camera? 43/59 44/59 Q6 How can I restore the network camera to default value? Q12 The process of upgrade firmware abort Q7 I cannot play the recorded video fileQ10 The cover of network camera is warm. Is it normal? A13 Camera from Internet ExplorerIp-discovery.comFree Ddns service 49/59 Current device Federal Communication Commission Interference Statement EU Countries Not Intended for Use EU Declaration of Conformity Weee Directive & Product Disposal 55/59 56/59 No Warranty 58/59 Network Camera User’s Manual 59/59
Top Page Image Contents