JVC GR-DVM5 Basic Recording, EN Video Recording, Tape Remaining Time, LCD Monitor And Viewfinder

Page 18

18 EN VIDEO RECORDING

Basic Recording

When a blank portion is left between recorded

scenes on the tape, the time code is interrupted

NOTE:

and errors may occur when editing the tape. To

avoid this, refer to “Recording From The Middle Of

Before continuing, perform the procedures listed

A Tape” ( pg. 20).

below:

To turn the beep sounds off,  pg. 31, 33.

Power ( pg. 13)

Tape Remaining Time

Loading A Cassette ( pg. 16)

VIDEO/MEMORY

Approximate tape remaining

 

time appears on the display.

 

“– h – – m” means the

 

camcorder is calculating the

Power Zoom Lever

remaining time. When the

remaining time reaches 2 minutes, the indication

Power Switch

starts blinking.

The time required to calculate and display the

 

Lock Button

remaining tape length, and the accuracy of the

calculation, may vary according to the type of tape

POWER/CHARGE Lamp

used.

LCD Monitor And Viewfinder

Recording Start/Stop Button

While using the LCD monitor:

 

1 Remove the lens cap. ( pg. 11)

Make sure the viewfinder is pushed back in. Pull

on the end of the LCD monitor and open the

2 Open the LCD monitor fully.

LCD monitor fully. It can rotate 270° (90°

3 Set the VIDEO/MEMORY Switch to “VIDEO”.

downward, 180° upward).

 

4 Set the Power Switch to “A” or “M” while

While using the viewfinder:

Make sure the LCD monitor is closed and

pressing down the Lock Button located on the

locked. Pull out the viewfinder fully.

switch.

 

The POWER/CHARGE lamp lights and the

180˚

camcorder enters the Record-Standby mode.

 

“PAUSE” is displayed.

 

To record in LP (Long Play) mode,  pg. 32.

 

5 To start recording, press the Recording Start/ Stop Button. “T REC” appears on the display while recording is in progress.

6 To stop recording, press the Recording Start/ Stop Button again. The camcorder re-enters the Record-Standby mode.

Approximate recording time

Tape

Recording mode

 

 

 

SP

LP

 

 

 

30 min.

30 min.

45 min.

 

 

 

60 min.

60 min.

90 min.

 

 

 

80 min.

80 min.

120 min.

 

 

 

90˚

NOTES:

The image will not appear simultaneously on the LCD monitor and the viewfinder. When the viewfinder is pulled out while the LCD monitor is opened, you can select which one to use. Set “PRIORITY” to the desired mode in SYSTEM Menu. ( pg. 31, 34)

Coloured bright spots may appear all over the LCD monitor or the viewfinder. However, this is not a malfunction. ( pg. 48)

NOTES:

If the Record-Standby mode continues for

5 minutes, the camcorder’s power shuts off automatically. To turn the camcorder on again, push back and pull out the viewfinder again or close and re-open the LCD monitor.

Image 18
Contents Digital Still Camera D.S.C. Recording Dear CustomerProgram AE with Special Effects Data BatteryWipe/Fader Effects LED LightSafety Precautions Page References Index EN Getting StartedControls ConnectorsIndicators Other PartsDuring D.S.C. Recording Only IntervalBright MIC During Video PlaybackDuring D.S.C. Playback BR I GHTBefore Using This Camcorder Provided Accessories How To Attach The Lens CapHow To Attach The Shoulder Strap Stopper How To Attach The Core FilterClose the core filter until it clicks shut Core filter Wind onceUsing The Battery Pack PowerCharging The Battery Pack Maximum continuous recording timeUsing AC Power Operation ModeData Battery System About BatteriesGrip Adjustment Language SettingsPower-Linked Operation Viewfinder Adjustment Brightness Adjustment Of The DisplayTripod Mounting Close the card cover CardTo protect valuable recordings To protect valuable files available only for SD Memory CardTape Remaining Time Basic RecordingEN Video Recording LCD Monitor And ViewfinderZoom Zooming Journalistic ShootingTime Code Zoom OutQuick Review To control the speaker volumeNormal Playback Video PlaybackVideo Playback EN Shuttle SearchBlank Search If using a VCR, go to . If not, go to step To AV connector AV cable provided Open the cover. markEN Video Playback Beam Effective Area indoor use Installing The BatteryControl Buttons And FunctionsPlayback Special Effects Frame-By-Frame PlaybackPlayback Zoom Approximate Number of Storable Images C. Recording ENBasic Shooting D.S.C. Snapshot Press SnapshotNormal Playback Of Images To cancel Interval Shooting modeAvailable only with the remote control.  pg C. PlaybackAuto Playback Of Images Index Playback Of FilesRemoving On-Screen Display To protect the currently displayed file Resetting The File NameProtecting Files Tape To a Memory Card MenuSetting Print Information Dpof Setting Deleting FilesTo Remove Protection Initialising a Memory Card EN Additional Features for D.S.CTo Reset The Number Of Prints EXECUTE, and pressMenus for Detailed Adjustment EN Menus without Sub MenusMenus with Sub Menus EN Menus for Detailed Adjustment Recording MenusBeep Remote Wide ModeDemo Mode Tele MacroLanguage CAM ResetPriority AUX MICPlayback Menus Blank Srch AV InputOFF / LCD / LCD/TV Live Slow To take a snapshot in the 5-second recording modeLED Light Second RecordingEN Features for Recording Night-ScopeSnapshot For Video Recording To return to automatic iris control Exposure Control Iris LockTo return to automatic exposure control To lock the exposure control and the irisWhite Balance Adjustment Backlight CompensationSpot Exposure Control Wipe Or Fader Effects To deactivate the selected effectSports Variable Shutter Speed 1/250 1/4000Set S/AV Input to A/V in or S IN*.  pg Dubbing To Or From a VCRTo use this camcorder as a recorder To use this camcorder as a playerDigital Dubbing EN EditingUsing USB cable Using DV cableUsing USB cable B Using DV cable To hear the dubbed sound during playback Audio DubbingInsert Editing To end Insert Editing, press START/STOP, then StopVideo and D.S.C. Recording PowerAdvanced features Video and D.S.C. PlaybackEN Troubleshooting Other problemsTroubleshooting EN Card Error DUB ErrorInsert Error Check CARD’S Write Protection SwitchUnit in Safeguard Mode Remove and Reattach Battery Cleaning The CamcorderUser Maintenance EN Unit in Safeguard Mode Eject and Reinsert TapeCassettes Battery PacksEN Cautions Memory CardsLCD Monitor Main UnitNot How To Handle a CD-ROM About moisture condensationSerious malfunctioning Ø3.5 mm, stereo CamcorderAC Adapter ReferencesDpof Setting Digital Print Order Format TermsRecording Capacity Software Installation and PC Connection Guide Limited Liability How to handle a CD-ROM For CyberLink DVD Solution System RequirementsSoftware Installation Windows Page Installing USB Mass Storage Class driver Updating Device Manager Windows 98SE onlyTo DV connector Connector Connecting the USB cableTo USB connector To IEEE1394Clips SettingStill DpofCopying Files to the PC Windows When using Windows 98SE Still imagesWhen using Windows 2000/Me/XP Click OKViewing the Contents of a Memory Card Macintosh Connections MacintoshStill images Dpof Setting data Navigation dataVideo Clips Playing Back Files on the PC Macintosh Overview of Enjoying the Moving or Still Images on the PC Via the USB cableTransfer the still images
Related manuals
Manual 92 pages 30.15 Kb Manual 88 pages 4.44 Kb Manual 12 pages 31.53 Kb