JVC GR-DVM5 manual Audio Dubbing, Insert Editing, To hear the dubbed sound during playback

46 EN EDITING

Audio Dubbing			● While an optional microphone is connected, the
			built-in microphone is disabled.
The audio track can be customised only when			● To perform Audio Dubbing with a video unit
			connected to the camcorder’s S/AV connector,
recorded in the 12-BIT and SP modes.			first set “S/AV INPUT” to “A/V IN” or “S IN” in
( pg. 32)			VIDEO Menu. ( pg. 31, 36)
● Use the provided remote control.			The “AUX” indication appears instead of “MIC”.
		Microphone
		Connector	Insert Editing
	Speaker		You can record a new scene into a previously
			recorded tape, replacing a section of the original
	START/		recording with minimal picture distortion at the in
			and outpoints. The original audio remains
	STOP		unchanged.
	PAUSE
		Stereo Microphone	● Use the provided remote control.
REW	PLAY
INSERT	STOP		NOTES:
	A.DUB
			● Before performing the following steps, make sure
1 Play back the tape to locate the point where
			that “TIME CODE” for “CAMERA DISPLAY” and
			“VIDEO DISPLAY” is set to “ON”.
editing will start, then press PAUSE (9).
			( pg. 31, 34, 36)
2 While holding A. DUB (D) on the remote
			● Insert Editing is not possible on a tape recorded in
control, press PAUSE (9). The “9D” and “MIC”			the LP mode or on a blank portion of a tape.
indicators appear.			1 Play back the tape, locate the Edit-Out point
3 Press PLAY (U), then begin “narrating”.
			and press PAUSE (9). Confirm the time code at
Speak into the microphone.			this point. ( pg. 19)

● To pause dubbing, press PAUSE (9).	2 Press REW (3) until the Edit-In point is
4 To end Audio Dubbing, press PAUSE (9),
	located, then press PAUSE (9).
then STOP (8).
	3 Press and hold INSERT (I) on the remote
To hear the dubbed sound during playback
	control, then press PAUSE (9). The “9I”
Set “NARRATION” to “ON” or “MIX”.
	indicator and the Time Code (min.:sec.) appear
( pg. 31, 35)
	and the camcorder enters Insert-Pause mode.

NOTES:

●Sound is not heard from the speaker during Audio Dubbing.

●When editing onto a tape that was recorded at

12-BIT, the old and new soundtracks are recorded separately.

●If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas.

●If feedback or howling occurs during TV playback, move the camcorder’s microphone away from the TV, or turn down the TV’s volume.

●If you change from 12-BIT to 16-BIT in mid- recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-BIT recording began.

●During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-BIT audio or a blank portion, Audio Dubbing stops.

●Audio dubbing is also possible using an optional microphone connected to the MIC connector.

4 Press START/STOP to begin editing.

●Confirm the insert at the time code you checked in step 1.

●To pause editing, press START/STOP. Press it again to resume editing.

5 To end Insert Editing, press START/STOP, then STOP (8).

NOTES:

●Program AE with special effects (
pg. 42) can be used to spice up the scenes being edited during Insert Editing.

●During Insert Editing, the date and time information changes.

●If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

●During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. (
pg. 50)