JVC TK-C676 Cable Connections, Make a 90 mm diameter hole in the ceiling, Connect the cables

Page 16

Connections & Installation

Cable Connections

Connect cables to the Ceiling Mount as described below.

1. Make a 90 mm diameter hole in the ceiling.

Diameter 90 mm

4. Connect the cables.

Connect the cables to the terminals on the Ceiling Mount. The four connection cables should consist of a AC 24V power cable, a coaxial cable, a control signal cable and an alarm signal cable.

2. Remove the cover from the Ceiling Mount.

Control signal cable

Alarm signal cable

Coaxial cable

To a remote controller such as RM-P2580

To a device with alarm input

RELEASE LOCK

Cover

To the monitor, etc.

Power cable

To the AC 24 V power supply

Ceiling mount

3. Pass the cables through the cover.

Make slits in the rubber cap on the cover as shown in the diagram below. Pull the cables through the hole in the ceiling and pass the cables through the slits.

Cap (Top)

Cap (Side)

Connector

Maximum diameter 31 mm

Tube

Maximum diameter 22 mm

33 mm or less

Drip-proof pipe

The diameter of the cover hole without the cap is 20.5 mm. When the camera is installed in a place where it may some- times be exposed to water splashes, for example under eaves, enclose cables in a drip-proof pipe.

TK-C655:Be sure to use a drip-proof pipe. The maximum diametre of the pipe connec- tor is 31 mm.

TK-C676:Be sure to use a water-drip pipe that com- plies with the IP52. standard. The maxi- mum diameter of the pipe connector is 31 mm.

When distributing the cable from the side, use the WB- S573 ceiling direct-mount bracket. In this case, the length of the connector should be 33 mm or less, and the maxi- mum diameter of the tube should be 22 mm or less.

AC 24V power cable

This cable connects the AC 24V power supply to the AC 24V input connector. To prevent connection errors and disconnections, the use of lug plate for connections to the AC 24 V INPUT connector is recommended.

When a 2-conductor VVF (Vinyl-insulated vinyl-sheath ca- ble) is used, the maximum connection length is as shown below. (These are merely the standard reference values.)

Maximum cable length

 

100 m

260 m

410 m

500 m

 

 

 

 

 

 

Wire diameter (mm)

 

1.0 or more

1.6 or more

2.0 or more

2.6 or more

 

 

 

 

 

 

CAUTIONS

●When a thin cables are used the cable resistance increases. As a result, when the power consumption of the unit is at its maximum level (during the simultaneous operation of panning and tilting) the effective voltage will drop.

If the voltage does drop while the camera is in use, perform- ance can become unstable and preset positions may not be reproduced accurately.

To prevent problems, use thicker cables that have a lower re- sistance or decrease the cable length by installing the power supply unit close to the camera. Attempt to reduce drops in voltage to less than 10% while the rated current level of the camera is flowing through the cable.

●Do not connect an AC 24V cable directly to an AC 230 V outlet. This will damage the unit.

●The AC 24 V power supply must be isolated from the primary line. (ISOLATED POWER ONLY)

●In order to prevent an excessive current flow through the pow- er supply wire or camera due to a short circuit, a fuse must be installed in the power supply line.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents TK-C655 TK-C676 LWT0200-001A-HImportant Safeguards Contents Features Provided Accessories4P Alarm cable 6P Alarm cable Screws M 4 x 12 mm Instructions Ceiling mountInstall the unit on a strong and stable surface Safety PrecautionsPower the unit with the rated power voltage Precautions for Correct Operation  Note on auto focusing  Preset positionsCamera setups with which auto focusing may be diffi- cult  Note on consumable partsControls, Connectors and Indicators Ceiling MountCamera Connector Female $ Machine ID SwitchSetting Switches Connector MaleSwitch settings P Observe the following points when connecting compoMulti-Drop Communication System Cable connections PMemo Point-to-Point Communication System Switch 7 Invalid Set to OFF Switch 8 onTerminal side of the Ceiling Mount Four wires must be connected Two wires must be connectedDuplex For example connection with an RM-P2580Switch Settings  Setting switchesCamera ID check procedure Machine IDBers on the RM-P2580 ExampleCable Connections Make a 90 mm diameter hole in the ceilingConnect the cables Remove the cover from the Ceiling MountAttach the cover Attaching a safety wire Attach the drop prevention wireAttaching the Ceiling Mount Attaching the CameraEnsure that the lock screw is loose Fit the cameraRotate the camera Tighten the lock screwSetup Procedure Setting the camera menus from an RM-P2580Press and hold the Menu button for 3 seconds Press the SET buttonNormal screen Menu Screen FlowMenu screen Function & Setting Initial Value Camera FUNCTION1 ScreenThis screen sets up the functions of the camera itself TK-C676 onlyCamera FUNCTION2 Screen Function & Setting1min Camera TITLE/ALARM Screen Alarm Input Polarity AlarmAlarm Output Alarm OUT1Camera Video Adjustment Screen Camera ALC screenSense UP MotionColour ModeColour Mode Alarm DisplayHome Motion Detect Screen Area EditAuto PAN/PATROL/TRACE Screen Iris Mode Position Function SET ScreenPosition Title Average PeakFactory Settings screen Private Mask Setup Camera Title Setup Title from the character areaPress the Tele button Repeat steps 5 and 6 for each title characterArea Title Setup Display the Setup menu on the cameraMove the cursor to Area Title Edit and press the SET button Press the FAR buttonAlarm Title Setup Repeat steps 5 to 7 for each alarm titleTITLE/ALARM screen is displayed TITLE/ALARM menuHome Motion Detect Setup Move the cursor to Area Edit and press the SET buttonHome Motion Detect menu Area Edit screenSet the auto pan mode and speed Auto PAN SetupAdjust the viewing angle of the start position Auto Patrol Setup Auto Trace Setup Move the cursor to Auto Trace SET and press the SET buttonSet the patrol start position Auto Trace SET screen is displayedPosition Title Setup SetupRepeat steps 5 to 7 for each title character Position Function SET screenAuto Return Setup Display the Setup menu on the camera. P.20, steps 1 toSet the return status using Auto Return function Display the Camera FUNCTION2 screenClamp the Ceiling Flush Mount Bracket Attaching a Ceiling Flush Mount Bracket Optional WB-S575Ceiling plate Attach the Ceiling Mount to the Ceiling Flush Mount Bracket Attach the camera to the Ceiling MountAttach the ceiling panel Connection CablesRemoving a Ceiling Flush Mount Bracket Optional WB-S575 Remove the ceiling panelRemove the camera Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedyPower cannot be Turned onSpecifications CameraPan/Tilt Mechanism GeneralExternal dimensions Unit mm Dimensions in combination with the WB-S575Ceiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C655/TK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 44 pages 37.37 Kb

TK-C676 specifications

The JVC TK-C676 is a professional-grade CCTV camera renowned for its impressive image quality and reliable performance in various surveillance applications. As part of JVC's reputable line of security products, the TK-C676 incorporates advanced technologies that make it a popular choice among security professionals and businesses alike.

One of the standout features of the TK-C676 is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crisp and clear images, ensuring optimal visibility even in challenging lighting conditions. The camera offers a resolution of 540 TV lines, which allows for detailed surveillance footage that can be crucial for identifying individuals or activities in monitored areas.

Another notable characteristic of the TK-C676 is its robust low-light performance. Thanks to its sense-up technology, the camera can automatically adjust its sensitivity in low-light environments, providing better image quality without the need for external lighting. This feature is particularly valuable for nighttime surveillance or in dimly lit indoor settings, enhancing the overall effectiveness of security measures.

The TK-C676 also excels in flexibility and adaptability with its mechanical IR cut filter. This technology allows for seamless switching between day and night modes, ensuring consistent image quality during both daytime and nighttime operation. This adaptability makes the camera suitable for various applications, including retail stores, parking lots, and public spaces.

Additionally, the JVC TK-C676 features a varifocal lens with a focal length of 3.5mm to 8mm, providing users with the ability to adjust the field of view based on specific surveillance needs. This versatility enables the camera to cover wide areas or focus on particular subjects, making it ideal for both indoor and outdoor placements.

In terms of durability, the TK-C676 is built to withstand harsh environmental conditions. With a sturdy housing that resists both water and dust, this camera can be installed in various locations without compromising on performance. This reliability is essential for continuous operation in demanding environments.

Overall, the JVC TK-C676 is a well-rounded CCTV camera that offers high-resolution imaging, excellent low-light performance, and adaptable features. Its combination of advanced technology, durable construction, and flexible camera options makes it a strong choice for anyone seeking a reliable surveillance solution. Whether for commercial, industrial, or residential applications, the TK-C676 proves to be a valuable asset in enhancing security measures.
Top Page Image Contents