JVC TK-C676 manual Attaching a Ceiling Flush Mount Bracket Optional WB-S575, Ceiling plate

Page 42

Others

Attaching a Ceiling Flush Mount Bracket (Optional WB-S575)

The ceiling flush mount bracket (optional WB-S575) allows the camera to be installed flush with the ceiling surface. In this case the ceiling material should have a thickness of between 5 mm and 31 mm.

Mount hole

3 positions

Anchor bolt mount holes

Clamping screw

Loosen

Clamping bracket

Clamping screw

Clamping screw

Mount screws (x 4)

1.

2.

Make a hole (diameter 200 mm) in the ceiling.

Prepare the Ceiling Flush Mount Bracket.

•Fully loosen the clamping screws (by turning them counterclock- wise).

•Move the clamping brackets toward the inside as shown in the diagram.

•Remove the four mount screws.

(1)

3. Clamp the Ceiling Flush Mount Bracket.

 

(1)

Fit the Ceiling Flush Mount Bracket into the hole in the ceiling.

Clamping screw

 

 

(2)

(2)

Ensure that the stoppers are pressing against the back of the

 

ceiling plate.

Stoppers

Anchor bolt mount

(3) Push the Ceiling Flush Mount Bracket all the way up and tight- en the three clamping screws (by turning them clockwise).

(3)

CAUTION

• Make sure that the clamping brackets grip the ceiling plate firmly.

• If the ceiling flush mount bracket rattles after the clamping screws are tightened, loosen them fully and tighten them again.

If anchor bolts can be used, attach them using M8 - M10 (or 3/8 inch) nuts.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents TK-C655 TK-C676 LWT0200-001A-HImportant Safeguards Contents 4P Alarm cable 6P Alarm cable Screws M 4 x 12 mm FeaturesProvided Accessories Instructions Ceiling mountSafety Precautions Install the unit on a strong and stable surfacePower the unit with the rated power voltage Precautions for Correct Operation Camera setups with which auto focusing may be diffi- cult  Note on auto focusing Preset positions  Note on consumable partsControls, Connectors and Indicators Ceiling MountSetting Switches Camera Connector Female$ Machine ID Switch Connector MaleMulti-Drop Communication System Switch settings PObserve the following points when connecting compo Cable connections PMemo Switch 7 Invalid Set to OFF Switch 8 on Point-to-Point Communication SystemTerminal side of the Ceiling Mount Duplex Four wires must be connectedTwo wires must be connected For example connection with an RM-P2580Switch Settings  Setting switchesBers on the RM-P2580 Camera ID check procedureMachine ID ExampleConnect the cables Cable ConnectionsMake a 90 mm diameter hole in the ceiling Remove the cover from the Ceiling MountAttach the cover Attaching the Ceiling Mount Attaching a safety wireAttach the drop prevention wire Attaching the CameraRotate the camera Ensure that the lock screw is looseFit the camera Tighten the lock screwPress and hold the Menu button for 3 seconds Setup ProcedureSetting the camera menus from an RM-P2580 Press the SET buttonMenu Screen Flow Normal screenMenu screen This screen sets up the functions of the camera itself Function & Setting Initial ValueCamera FUNCTION1 Screen TK-C676 onlyFunction & Setting Camera FUNCTION2 Screen1min Camera TITLE/ALARM Screen Alarm Output Alarm Input PolarityAlarm Alarm OUT1Camera Video Adjustment Screen Camera ALC screenColour Sense UPMotion ModeHome Motion Detect Screen Colour ModeAlarm Display Area EditAuto PAN/PATROL/TRACE Screen Position Title Iris ModePosition Function SET Screen Average PeakFactory Settings screen Private Mask Setup Press the Tele button Camera Title SetupTitle from the character area Repeat steps 5 and 6 for each title characterMove the cursor to Area Title Edit and press the SET button Area Title SetupDisplay the Setup menu on the camera Press the FAR buttonTITLE/ALARM screen is displayed Alarm Title SetupRepeat steps 5 to 7 for each alarm title TITLE/ALARM menuHome Motion Detect menu Home Motion Detect SetupMove the cursor to Area Edit and press the SET button Area Edit screenAuto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Set the patrol start position Auto Trace SetupMove the cursor to Auto Trace SET and press the SET button Auto Trace SET screen is displayedRepeat steps 5 to 7 for each title character Position Title SetupSetup Position Function SET screenSet the return status using Auto Return function Auto Return SetupDisplay the Setup menu on the camera. P.20, steps 1 to Display the Camera FUNCTION2 screenAttaching a Ceiling Flush Mount Bracket Optional WB-S575 Clamp the Ceiling Flush Mount BracketCeiling plate Attach the ceiling panel Attach the Ceiling Mount to the Ceiling Flush Mount BracketAttach the camera to the Ceiling Mount Connection CablesRemove the camera Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the ceiling panel Check the release labels thoroughly before removalPower cannot be TroubleshootingSymptom Cause Information Remedy Turned onPan/Tilt Mechanism SpecificationsCamera GeneralCeiling mount hole External dimensions Unit mmDimensions in combination with the WB-S575 WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C655/TK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 44 pages 37.37 Kb

TK-C676 specifications

The JVC TK-C676 is a professional-grade CCTV camera renowned for its impressive image quality and reliable performance in various surveillance applications. As part of JVC's reputable line of security products, the TK-C676 incorporates advanced technologies that make it a popular choice among security professionals and businesses alike.

One of the standout features of the TK-C676 is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crisp and clear images, ensuring optimal visibility even in challenging lighting conditions. The camera offers a resolution of 540 TV lines, which allows for detailed surveillance footage that can be crucial for identifying individuals or activities in monitored areas.

Another notable characteristic of the TK-C676 is its robust low-light performance. Thanks to its sense-up technology, the camera can automatically adjust its sensitivity in low-light environments, providing better image quality without the need for external lighting. This feature is particularly valuable for nighttime surveillance or in dimly lit indoor settings, enhancing the overall effectiveness of security measures.

The TK-C676 also excels in flexibility and adaptability with its mechanical IR cut filter. This technology allows for seamless switching between day and night modes, ensuring consistent image quality during both daytime and nighttime operation. This adaptability makes the camera suitable for various applications, including retail stores, parking lots, and public spaces.

Additionally, the JVC TK-C676 features a varifocal lens with a focal length of 3.5mm to 8mm, providing users with the ability to adjust the field of view based on specific surveillance needs. This versatility enables the camera to cover wide areas or focus on particular subjects, making it ideal for both indoor and outdoor placements.

In terms of durability, the TK-C676 is built to withstand harsh environmental conditions. With a sturdy housing that resists both water and dust, this camera can be installed in various locations without compromising on performance. This reliability is essential for continuous operation in demanding environments.

Overall, the JVC TK-C676 is a well-rounded CCTV camera that offers high-resolution imaging, excellent low-light performance, and adaptable features. Its combination of advanced technology, durable construction, and flexible camera options makes it a strong choice for anyone seeking a reliable surveillance solution. Whether for commercial, industrial, or residential applications, the TK-C676 proves to be a valuable asset in enhancing security measures.
Top Page Image Contents