JVC TK-C676 manual Features, Provided Accessories, Instructions Ceiling mount

Page 4

Introduction

Features

DSP with a wide dynamic range

Even objects that have a large difference in brightness can be monitored clearly.

Day/night surveillance

When the light is low, the camera pictures can be switched automatically to black and white pictures.

The camera is also compatible with IR illumination (wave- length 850 nm to 880 nm).

Private masking facility

When the camera target area contains an area that is re- quired to be hidden the camera can be set accordingly in order to mask it.

High-speed pan/tilt table

The high-speed rotating table with a horizontal panning speed of 300°/sec. and a vertical tilting speed of 180°/sec. makes it possible to recall a preset position quickly.

High-sensitivity CCD and bright zoom lens

TK-C655:The CCD features an improved sensitivity of near- ly 70% over the previous model and the zoom lens has a large aperture ratio of f1.6 (at WIDE end). These features provide the camera with a high sensitivity of 2.0 lx in the color mode (50% output, AGC 20 dB).

TK-C676:The CCD features an improved sensitivity of near- ly 70% over the previous model and the zoom lens has a large aperture ratio of f1.4 (at WIDE end). These features provide the camera with a high sensitivity of 0.5 lx in the color mode (25% output, AGC 20 dB, WIDE end, electronic sense up x2).

Optical zoom lens (TK-C655 only)

Detailed surveillance can be performed with the approx. x25 optical zoom lens.

Optical + electronic zooming (TK-C676 only)

The x27 optical zoom lens and x10 electronic zoom circuit- ry allows the camera to be used even in surveillance situa- tions in which the object is very small.

Simplified waterproof design (TK-C676 only)

The simplified waterproof design (IEC529) of the camera allows it to be installed in many locations, including under eaves, provided that it is not subjected to direct water splash. (However, note that the camera cannot be used outdoors.)

Provided Accessories

 

DOME TYPE CAMERA

 

 

TK-C655

(B)

 

 

INSTRUCTIONS

TK-C676

 

 

 

Screw

 

 

 

(M3 12 mm)

Cable plate

Instructions

Ceiling mount

For cable plate

4P Alarm cable

6P Alarm cable

Screws (M 4 x 12 mm)

 

 

For the ceiling flush mount bracket

4

Image 4 Contents
TK-C655 TK-C676 LWT0200-001A-HImportant Safeguards Contents Features Provided Accessories4P Alarm cable 6P Alarm cable Screws M 4 x 12 mm Instructions Ceiling mountInstall the unit on a strong and stable surface Safety PrecautionsPower the unit with the rated power voltage Precautions for Correct Operation  Note on auto focusing  Preset positionsCamera setups with which auto focusing may be diffi- cult  Note on consumable partsControls, Connectors and Indicators Ceiling MountCamera Connector Female $ Machine ID SwitchSetting Switches Connector MaleSwitch settings P Observe the following points when connecting compoMulti-Drop Communication System Cable connections PMemo Point-to-Point Communication System Switch 7 Invalid Set to OFF Switch 8 onTerminal side of the Ceiling Mount Four wires must be connected Two wires must be connectedDuplex For example connection with an RM-P2580Switch Settings  Setting switchesCamera ID check procedure Machine IDBers on the RM-P2580 ExampleCable Connections Make a 90 mm diameter hole in the ceilingConnect the cables Remove the cover from the Ceiling MountAttach the cover Attaching a safety wire Attach the drop prevention wireAttaching the Ceiling Mount Attaching the CameraEnsure that the lock screw is loose Fit the cameraRotate the camera Tighten the lock screwSetup Procedure Setting the camera menus from an RM-P2580Press and hold the Menu button for 3 seconds Press the SET buttonNormal screen Menu Screen FlowMenu screen Function & Setting Initial Value Camera FUNCTION1 ScreenThis screen sets up the functions of the camera itself TK-C676 onlyCamera FUNCTION2 Screen Function & Setting1min Camera TITLE/ALARM Screen Alarm Input Polarity AlarmAlarm Output Alarm OUT1Camera Video Adjustment Screen Camera ALC screenSense UP MotionColour ModeColour Mode Alarm DisplayHome Motion Detect Screen Area EditAuto PAN/PATROL/TRACE Screen Iris Mode Position Function SET ScreenPosition Title Average PeakFactory Settings screen Private Mask Setup Camera Title Setup Title from the character areaPress the Tele button Repeat steps 5 and 6 for each title characterArea Title Setup Display the Setup menu on the cameraMove the cursor to Area Title Edit and press the SET button Press the FAR buttonAlarm Title Setup Repeat steps 5 to 7 for each alarm titleTITLE/ALARM screen is displayed TITLE/ALARM menuHome Motion Detect Setup Move the cursor to Area Edit and press the SET buttonHome Motion Detect menu Area Edit screenSet the auto pan mode and speed Auto PAN SetupAdjust the viewing angle of the start position Auto Patrol Setup Auto Trace Setup Move the cursor to Auto Trace SET and press the SET buttonSet the patrol start position Auto Trace SET screen is displayedPosition Title Setup SetupRepeat steps 5 to 7 for each title character Position Function SET screenAuto Return Setup Display the Setup menu on the camera. P.20, steps 1 toSet the return status using Auto Return function Display the Camera FUNCTION2 screenClamp the Ceiling Flush Mount Bracket Attaching a Ceiling Flush Mount Bracket Optional WB-S575Ceiling plate Attach the Ceiling Mount to the Ceiling Flush Mount Bracket Attach the camera to the Ceiling MountAttach the ceiling panel Connection CablesRemoving a Ceiling Flush Mount Bracket Optional WB-S575 Remove the ceiling panelRemove the camera Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedyPower cannot be Turned onSpecifications CameraPan/Tilt Mechanism GeneralExternal dimensions Unit mm Dimensions in combination with the WB-S575Ceiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C655/TK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 44 pages 37.37 Kb