JVC TK-C676 Removing a Ceiling Flush Mount Bracket Optional WB-S575, Remove the ceiling panel

Page 44

Others

Removing a Ceiling Flush Mount Bracket (Optional WB-S575)

3.

<Check the release labels thoroughly before removal.>

1. Remove the ceiling panel.

Pull the ceiling panel and disengage the two hooks.

2. Remove the camera.

Clamping bracket

Remove the camera from the Ceiling Mount by reversing the at- taching procedure.

☞ P. 18, “Attaching the Camera”

4.

Stoppers

3. Loosen the clamping screws of the Ceiling Flush Mount Bracket.

•Loosen the three clamping screws (by turning them counterclock- wise).

•Make sure that the clamping brackets move inwards.

5.

Release label

6.

*

Push the stopper release lever upwards with a screwdriver, etc.

4. Lower the Ceiling Flush Mount Bracket until the stoppers contact the ceiling plate.

5. Push up the stopper release lever, marked (*) in the figure, using a screwdriver.

•While holding the Ceiling Flush Mount Bracket from below so that it does not drop, push up the one of the three stopper release levers marked (*)using a screwdriver or a similar tool.

•If the ceiling plate is thick and the stoppers cannot be released easily, push up two of the stopper release levers (including the one marked (*)).

6.Pull out the Ceiling Flush Mount Bracket from the hole in the ceiling.

Tilt the Ceiling Flush Mount Bracket and move it obliquely down- ward to remove it.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents TK-C655 TK-C676 LWT0200-001A-HImportant Safeguards Contents Features Provided Accessories4P Alarm cable 6P Alarm cable Screws M 4 x 12 mm Instructions Ceiling mountPower the unit with the rated power voltage Safety PrecautionsInstall the unit on a strong and stable surface Precautions for Correct Operation  Note on auto focusing  Preset positionsCamera setups with which auto focusing may be diffi- cult  Note on consumable partsControls, Connectors and Indicators Ceiling MountCamera Connector Female $ Machine ID SwitchSetting Switches Connector MaleSwitch settings P Observe the following points when connecting compoMulti-Drop Communication System Cable connections PMemo Terminal side of the Ceiling Mount Switch 7 Invalid Set to OFF Switch 8 onPoint-to-Point Communication System Four wires must be connected Two wires must be connectedDuplex For example connection with an RM-P2580Switch Settings  Setting switchesCamera ID check procedure Machine IDBers on the RM-P2580 ExampleCable Connections Make a 90 mm diameter hole in the ceilingConnect the cables Remove the cover from the Ceiling MountAttach the cover Attaching a safety wire Attach the drop prevention wireAttaching the Ceiling Mount Attaching the CameraEnsure that the lock screw is loose Fit the cameraRotate the camera Tighten the lock screwSetup Procedure Setting the camera menus from an RM-P2580Press and hold the Menu button for 3 seconds Press the SET buttonMenu screen Menu Screen FlowNormal screen Function & Setting Initial Value Camera FUNCTION1 ScreenThis screen sets up the functions of the camera itself TK-C676 only1min Function & SettingCamera FUNCTION2 Screen Camera TITLE/ALARM Screen Alarm Input Polarity AlarmAlarm Output Alarm OUT1Camera Video Adjustment Screen Camera ALC screenSense UP MotionColour ModeColour Mode Alarm DisplayHome Motion Detect Screen Area EditAuto PAN/PATROL/TRACE Screen Iris Mode Position Function SET ScreenPosition Title Average PeakFactory Settings screen Private Mask Setup Camera Title Setup Title from the character areaPress the Tele button Repeat steps 5 and 6 for each title characterArea Title Setup Display the Setup menu on the cameraMove the cursor to Area Title Edit and press the SET button Press the FAR buttonAlarm Title Setup Repeat steps 5 to 7 for each alarm titleTITLE/ALARM screen is displayed TITLE/ALARM menuHome Motion Detect Setup Move the cursor to Area Edit and press the SET buttonHome Motion Detect menu Area Edit screenAdjust the viewing angle of the start position Auto PAN SetupSet the auto pan mode and speed Auto Patrol Setup Auto Trace Setup Move the cursor to Auto Trace SET and press the SET buttonSet the patrol start position Auto Trace SET screen is displayedPosition Title Setup SetupRepeat steps 5 to 7 for each title character Position Function SET screenAuto Return Setup Display the Setup menu on the camera. P.20, steps 1 toSet the return status using Auto Return function Display the Camera FUNCTION2 screenCeiling plate Attaching a Ceiling Flush Mount Bracket Optional WB-S575Clamp the Ceiling Flush Mount Bracket Attach the Ceiling Mount to the Ceiling Flush Mount Bracket Attach the camera to the Ceiling MountAttach the ceiling panel Connection CablesRemoving a Ceiling Flush Mount Bracket Optional WB-S575 Remove the ceiling panelRemove the camera Check the release labels thoroughly before removalTroubleshooting Symptom Cause Information RemedyPower cannot be Turned onSpecifications CameraPan/Tilt Mechanism GeneralExternal dimensions Unit mm Dimensions in combination with the WB-S575Ceiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C655/TK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 44 pages 37.37 Kb

TK-C676 specifications

The JVC TK-C676 is a professional-grade CCTV camera renowned for its impressive image quality and reliable performance in various surveillance applications. As part of JVC's reputable line of security products, the TK-C676 incorporates advanced technologies that make it a popular choice among security professionals and businesses alike.

One of the standout features of the TK-C676 is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crisp and clear images, ensuring optimal visibility even in challenging lighting conditions. The camera offers a resolution of 540 TV lines, which allows for detailed surveillance footage that can be crucial for identifying individuals or activities in monitored areas.

Another notable characteristic of the TK-C676 is its robust low-light performance. Thanks to its sense-up technology, the camera can automatically adjust its sensitivity in low-light environments, providing better image quality without the need for external lighting. This feature is particularly valuable for nighttime surveillance or in dimly lit indoor settings, enhancing the overall effectiveness of security measures.

The TK-C676 also excels in flexibility and adaptability with its mechanical IR cut filter. This technology allows for seamless switching between day and night modes, ensuring consistent image quality during both daytime and nighttime operation. This adaptability makes the camera suitable for various applications, including retail stores, parking lots, and public spaces.

Additionally, the JVC TK-C676 features a varifocal lens with a focal length of 3.5mm to 8mm, providing users with the ability to adjust the field of view based on specific surveillance needs. This versatility enables the camera to cover wide areas or focus on particular subjects, making it ideal for both indoor and outdoor placements.

In terms of durability, the TK-C676 is built to withstand harsh environmental conditions. With a sturdy housing that resists both water and dust, this camera can be installed in various locations without compromising on performance. This reliability is essential for continuous operation in demanding environments.

Overall, the JVC TK-C676 is a well-rounded CCTV camera that offers high-resolution imaging, excellent low-light performance, and adaptable features. Its combination of advanced technology, durable construction, and flexible camera options makes it a strong choice for anyone seeking a reliable surveillance solution. Whether for commercial, industrial, or residential applications, the TK-C676 proves to be a valuable asset in enhancing security measures.
Top Page Image Contents