JVC TK-C676 Cover, Camera Connector Female, @ Drop Prevention Hook, # Clamping Holes x, Lens

Page 9

# % $

! #

@

(Setting switch side)

0Cover

For protection against water drips. Slit the rubber cap on

this cover and pass the cable through the slits. ☞ P. 16

!Camera Connector (Female)

Connect to ^, the Male Connector on the camera.

@Drop Prevention Hook

Attach the Drop Prevention Wire & to this hook to prevent the camera from falling.

#Clamping Holes (x 4)

Attach the camera to a ceiling or to a Ceiling Flush Mount Bracket (optionally available) using these holes.

$[MACHINE ID] Switch

When an RS-485 communication system is used, for ex- ample when using the camera in a system controlled by an RM-P2580, set the camera IDs individually for each

camera. ☞ P. 15

%Setting Switches

Use these to set the PROTOCOL, etc. ☞ P. 14

&

^

*

⁄

) (

^Connector (Male)

Connect to !, the Female Camera Connector on the Ceil- ing Mount.

&Drop Prevention Wire

Attach this wire to the Drop Prevention Hook @ on the Ceiling Mount.

*Camera Clamping Bracket

In order to clamp the camera onto the Ceiling Mount, in- sert and tighten the Locking Screw 4 into this bracket.

(Lens

The lens cannot be replaced.

)Dome Cover

The dome cover is fragile. Take care when handling it.

⁄Camera Body Cover

Do not remove the camera body cover while the camera is installed on a ceiling. Doing so will cause the dome cover to fall down.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents LWT0200-001A-H TK-C655 TK-C676Important Safeguards Contents Provided Accessories Features4P Alarm cable 6P Alarm cable Screws M 4 x 12 mm Instructions Ceiling mountSafety Precautions Install the unit on a strong and stable surfacePower the unit with the rated power voltage Precautions for Correct Operation  Preset positions  Note on auto focusingCamera setups with which auto focusing may be diffi- cult  Note on consumable partsCeiling Mount Controls, Connectors and Indicators$ Machine ID Switch Camera Connector FemaleSetting Switches Connector MaleObserve the following points when connecting compo Switch settings PMulti-Drop Communication System Cable connections PMemo Switch 7 Invalid Set to OFF Switch 8 on Point-to-Point Communication SystemTerminal side of the Ceiling Mount Two wires must be connected Four wires must be connectedDuplex For example connection with an RM-P2580 Setting switches Switch SettingsMachine ID Camera ID check procedureBers on the RM-P2580 ExampleMake a 90 mm diameter hole in the ceiling Cable ConnectionsConnect the cables Remove the cover from the Ceiling MountAttach the cover Attach the drop prevention wire Attaching a safety wireAttaching the Ceiling Mount Attaching the CameraFit the camera Ensure that the lock screw is looseRotate the camera Tighten the lock screwSetting the camera menus from an RM-P2580 Setup ProcedurePress and hold the Menu button for 3 seconds Press the SET buttonMenu Screen Flow Normal screenMenu screen Camera FUNCTION1 Screen Function & Setting Initial ValueThis screen sets up the functions of the camera itself TK-C676 onlyFunction & Setting Camera FUNCTION2 Screen1min Camera TITLE/ALARM Screen Alarm Alarm Input PolarityAlarm Output Alarm OUT1Camera ALC screen Camera Video Adjustment ScreenMotion Sense UPColour ModeAlarm Display Colour ModeHome Motion Detect Screen Area EditAuto PAN/PATROL/TRACE Screen Position Function SET Screen Iris ModePosition Title Average PeakFactory Settings screen Private Mask Setup Title from the character area Camera Title SetupPress the Tele button Repeat steps 5 and 6 for each title characterDisplay the Setup menu on the camera Area Title SetupMove the cursor to Area Title Edit and press the SET button Press the FAR buttonRepeat steps 5 to 7 for each alarm title Alarm Title SetupTITLE/ALARM screen is displayed TITLE/ALARM menuMove the cursor to Area Edit and press the SET button Home Motion Detect SetupHome Motion Detect menu Area Edit screenAuto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Move the cursor to Auto Trace SET and press the SET button Auto Trace SetupSet the patrol start position Auto Trace SET screen is displayedSetup Position Title SetupRepeat steps 5 to 7 for each title character Position Function SET screenDisplay the Setup menu on the camera. P.20, steps 1 to Auto Return SetupSet the return status using Auto Return function Display the Camera FUNCTION2 screenAttaching a Ceiling Flush Mount Bracket Optional WB-S575 Clamp the Ceiling Flush Mount BracketCeiling plate Attach the camera to the Ceiling Mount Attach the Ceiling Mount to the Ceiling Flush Mount BracketAttach the ceiling panel Connection CablesRemove the ceiling panel Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the camera Check the release labels thoroughly before removalSymptom Cause Information Remedy TroubleshootingPower cannot be Turned onCamera SpecificationsPan/Tilt Mechanism GeneralDimensions in combination with the WB-S575 External dimensions Unit mmCeiling mount hole WB-S575 Ceiling flush mount bracket + Ceiling panelTK-C655/TK-C676 Dome Type Camera
Related manuals
Manual 216 pages 55.17 Kb Manual 44 pages 37.37 Kb

TK-C676 specifications

The JVC TK-C676 is a professional-grade CCTV camera renowned for its impressive image quality and reliable performance in various surveillance applications. As part of JVC's reputable line of security products, the TK-C676 incorporates advanced technologies that make it a popular choice among security professionals and businesses alike.

One of the standout features of the TK-C676 is its high-resolution imaging capability. With a 1/3-inch CCD sensor, this camera delivers crisp and clear images, ensuring optimal visibility even in challenging lighting conditions. The camera offers a resolution of 540 TV lines, which allows for detailed surveillance footage that can be crucial for identifying individuals or activities in monitored areas.

Another notable characteristic of the TK-C676 is its robust low-light performance. Thanks to its sense-up technology, the camera can automatically adjust its sensitivity in low-light environments, providing better image quality without the need for external lighting. This feature is particularly valuable for nighttime surveillance or in dimly lit indoor settings, enhancing the overall effectiveness of security measures.

The TK-C676 also excels in flexibility and adaptability with its mechanical IR cut filter. This technology allows for seamless switching between day and night modes, ensuring consistent image quality during both daytime and nighttime operation. This adaptability makes the camera suitable for various applications, including retail stores, parking lots, and public spaces.

Additionally, the JVC TK-C676 features a varifocal lens with a focal length of 3.5mm to 8mm, providing users with the ability to adjust the field of view based on specific surveillance needs. This versatility enables the camera to cover wide areas or focus on particular subjects, making it ideal for both indoor and outdoor placements.

In terms of durability, the TK-C676 is built to withstand harsh environmental conditions. With a sturdy housing that resists both water and dust, this camera can be installed in various locations without compromising on performance. This reliability is essential for continuous operation in demanding environments.

Overall, the JVC TK-C676 is a well-rounded CCTV camera that offers high-resolution imaging, excellent low-light performance, and adaptable features. Its combination of advanced technology, durable construction, and flexible camera options makes it a strong choice for anyone seeking a reliable surveillance solution. Whether for commercial, industrial, or residential applications, the TK-C676 proves to be a valuable asset in enhancing security measures.
Top Page Image Contents