JVC TK-C676 manual Auto PAN Setup, Set the auto pan mode and speed

1 to 4

AUTO PAN Setup

Use the AUTO PAN screen to set the auto pan function, which allows the camera to be revolved slowly in a horizontal direction) The auto pan function has three modes, the RETURN mode for continual movement between two positions, the RIGHT mode for clock-wise rotation and the LEFT mode for counterclockwise rotation.

	Slow movement
of	Picture		of
Picture	return
position		position
start

MENU button

SET button

1. Select the camera. ( ☞ RM-P2580 Instruction manual)

CAMERA button → Numeric key (camera number) → ENTER button. The picture of the selected camera is output.

2. Display the SETUP menu on the camera.

( ☞ P. 20, steps )

MENU button (3 sec.) → Select “CAMERA” with the PAN/TILT lever

→ SET button.

3.Tilt the PAN/TILT lever up or down to move the cur- sor (>) to “AUTO PAN/PATROL TRACE” and press the SET button.

The AUTO PAN/PATROL/TRACE menu is displayed.

			REMOTE CONTROL UNIT RM-P2580
SETUP		CAMERA	POSITION
		POWER
MENU	SET	ALARM	AUTO	F-1	F-2	F-3
		KEY LOCK

CAMERA

	LENS			CAMERA/POSITION			PAN/TILT	buttons
	SPEED		1	2	3	CAMERA	POSI-
							TION
	IRIS		4	5	6	1	2
CLOSE		OPEN				OPTION	OPTION	PAN/TILT
NEAR	FOCUS	FAR	7	8	9	AUTO	AUTO
	AF					PAN	PATROL	lever
WIDE	ZOOM	TELE	CLEAR	0	ENTER
				/HOME
			ENTER button
	FAR button						TELE button
						WIDE button
NEAR button
– – – A U T O P A N / P A T R O L / T R A C E – – –
A U T O P A N M O D E							R E T U R N
A U T O P A N S P E E D							N O R M A L
A . P A N S T A R T P O S . S E T . .
A . P A N R E T U R N P O S . S E T . .
A U T O P A T R O L S E T . .
A U T O T R A C E S E T . .
R M A . P A N K E Y							A . P A N
R M A . P A T R O L K E Y							A . P A T R O L

AUTO PAN/PATROL/TRACE menu

4. Set the auto pan mode and speed.

•Select the “AUTO PAN MODE” item and then select either RE- TURN (continual movement between two positions), RIGHT(clockwise rotation) or LEFT (counterclockwise rotation).

•Select the “AUTO PAN SPEED” item and then select either LOW, NORMAL or HIGH.

5.Move the cursor (>) to “A. PAN START POSITION SET” and press the SET button.

The START POSITION SET screen is displayed.

6. Adjust the viewing angle of the start position.

•Use the PAN/TILT lever, FOCUS button and ZOOM button to ad- just the viewing angle.

•Tilting of the camera and changes in lens controls such as the FOCUS and ZOOM settings are not available at the return posi- tion.

7.Press the MENU button.

The AUTO PAN/PATROL/TRACE screen shows “DATA SAVED” to indicate that the viewing angle for the start position has been regis- tered.

8. Move the cursor (>) to “A. PAN RETURN POSITION SET”and press the SET button. (RETURN mode only)

The RETURN POSITION SET screen is displayed.

– – – S T A R T P O S I T I O N S E T – – –

P U S H M E N U / S A V E & R E T U R N

START POSITION SET screen

– – – R E T U R N P O S I T I O N S E T – – –

P U S H M E N U / S A V E & R E T U R N

RETURN POSITION SET screen

9. Adjust the viewing angle of the return position. (RETURN mode only)

Pan the camera in the right and left directions and adjust the view- ing angle.

10. Press the MENU button.

MEMO

•It is not possible to tilt the camera or change the lens settings at the return position.

•If the SET or MENU buttons are pressed while the camera is mov- ing, the correct settings cannot be registered. Make sure that the camera is stationary before pressing the SET or MENU buttons.

•The screen returns to the previous menu.

After the above setup, auto panning of the camera can be started by pressing the AUTO PAN button on the RM-P2580.

☞“Auto Panning” in the RM-P2580 Instruction manual.

37