Auto Trace Setup, Set the patrol start position

JVC TK-C676 manual Auto Trace Setup, Move the cursor to Auto Trace SET and press the SET button

Page 39

AUTO TRACE Setup

Use the AUTO TRACE screen to set the auto trace function, which stores and reproduces the actions of a manual camera opera-

tion (up to 30 seconds).

MENU button

SET button

			REMOTE CONTROL UNIT RM-P2580
SETUP		CAMERA	POSITION
SETUP		POWER
MENU	SET	ALARM	AUTO	F-1	F-2	F-3
		KEY LOCK

	LENS			CAMERA/POSITION			PAN/TILT
	SPEED		1	2	3	CAMERA	POSI-
							TION
	IRIS		4	5	6	1	2
CLOSE	IRIS	OPEN				OPTION	OPTION
NEAR	FOCUS	FAR	7	8	9	AUTO	AUTO
	AF		7	8	9	PAN	PATROL
WIDE	ZOOM	TELE	CLEAR	0	ENTER
				/HOME

ZOOM button ENTER button

FOCUS button

– – – M E N U – – –

C A M . F U N C T I O N 1 . . C A M . F U N C T I O N 2 . .

C A M . T I T L E / A L A R M . .

C A M .	V I D E O A D J U S T . .
C A M .	A L C . .
H O M E M O T I O N D E T E C T . .
A U T O	P A N / P A T R O L / T R A C E . .
P O S I . F U N C T I O N S E T . .
F A C T O R Y S E T T I N G S . .


– – A U T O P A N / P A T R O L / T R A C E – –
A U T O	P A N M O D E	R E T U R N
A U T O	P A N S P E E D	N O R M A L

A . P A N S T A R T	P O S .	S E T . .
A . P A N R E T U R N P O S . S E T . .
A U T O P A T R O L	S E T . .
A U T O T R A C E S E T . .
R M A . P A N K E Y		A . P A N
R M A . P A T R O L	K E Y	A . P A T R O L

Numeric keys

CAMERA buttons

PAN/TILT lever

1. Select the camera. ( ☞ RM-P2580 Instruction manual)

CAMERA button → Numeric key (camera number) → ENTER button. The picture of the selected camera is output.

2. Display the SETUP menu on the camera. ( ☞ P. 20, steps 1 to 4 )

MENU button (3 sec.) → Select “CAMERA” with the PAN/TILT lever

→ SET button.

3.Tilt the PAN/TILT lever up or down to move the cur- sor (>) to “AUTO PAN/PATROL TRACE” and press the SET button.

The AUTO PAN/PATROL/TRACE menu is displayed.

4. Move the cursor (>) to “AUTO TRACE SET” and press the SET button.

The AUTO TRACE SET screen is displayed.

5. Set the patrol start position.

Using the PAN/TILT lever and the ZOOM and FOCUS buttons, set the camera position at which the auto trace function is to be started.

6. Press the SET button (to start memorization of man- ual camera operations).

•Auto trace starts. Operate the camera using the PAN/TILT lever, and the ZOOM and FOCUS buttons.

•The Auto trace function can memorize camera operations for up to 30 seconds, during this period “LEARNING” is displayed in the screen.

•Storage finishes automatically after 30 seconds.

•Perform step 7 only when finishing the storage but before 30 sec- onds elapses.

– – – A U T O T R A C E S E T – – –

P U S H S E T → L E A R N

– – – A U T O T R A C E S E T – – –

L E A R N I N G

7. Press the SET button to end the memorization of manual camera operations.

•Auto trace ends and the screen returns to the AUTO PAN/PA- TROL/TRACE menu.

8.Press the MENU button.

•The screen returns to the AUTO PAN/PATROL/TRACE menu.

MEMO

●The PAN/TILT position in the item “AUTO TRACE” function can be set and operated only between 0° and 90° (it cannot be set and operated between 90° and 180°) even when the item “FLIP” is set to DIGITAL.

●The electronic zoom can be set up to x2. (It is not permitted to set an elec- tronic zoom ratio of more than x2.)

RM-P2580 units need to be configured to use replay movements stored by the Auto Trace func- tion Use the AUTO PAN or AUTO TRACE buttons on the RM-P2580 to do this:

To let the camera execute reproduction of the auto trace operation, it is required to set the auto trace function in the AUTO PAN or AUTO TRACE button of the RM-P2580.

☞P. 30, Items “RM. A. PAN KEY” and “RM. A. PATROL KEY”.

When the button to which the auto trace function is set is pressed, the lamp in the button lights up and auto trace reproduction starts.

The auto trace reproduction will repeat continually with a pause of 30 seconds between each operation.

To end the auto trace reproduction, press the button to which the auto trace function is set again so that the lamp in the button turns off.

Image 39

Contents

LWT0200-001A-H TK-C655 TK-C676Important Safeguards Contents Instructions Ceiling mount FeaturesProvided Accessories 4P Alarm cable 6P Alarm cable Screws M 4 x 12 mmSafety Precautions Install the unit on a strong and stable surfacePower the unit with the rated power voltage Precautions for Correct Operation Note on consumable parts Note on auto focusing Preset positions Camera setups with which auto focusing may be diffi- cultCeiling Mount Controls, Connectors and IndicatorsConnector Male Camera Connector Female$ Machine ID Switch Setting SwitchesCable connections P Switch settings PObserve the following points when connecting compo Multi-Drop Communication SystemMemo Switch 7 Invalid Set to OFF Switch 8 on Point-to-Point Communication SystemTerminal side of the Ceiling Mount For example connection with an RM-P2580 Four wires must be connectedTwo wires must be connected Duplex Setting switches Switch SettingsExample Camera ID check procedureMachine ID Bers on the RM-P2580Remove the cover from the Ceiling Mount Cable ConnectionsMake a 90 mm diameter hole in the ceiling Connect the cablesAttach the cover Attaching the Camera Attaching a safety wireAttach the drop prevention wire Attaching the Ceiling MountTighten the lock screw Ensure that the lock screw is looseFit the camera Rotate the cameraPress the SET button Setup ProcedureSetting the camera menus from an RM-P2580 Press and hold the Menu button for 3 secondsMenu Screen Flow Normal screenMenu screen TK-C676 only Function & Setting Initial ValueCamera FUNCTION1 Screen This screen sets up the functions of the camera itselfFunction & Setting Camera FUNCTION2 Screen1min Camera TITLE/ALARM Screen Alarm OUT1 Alarm Input PolarityAlarm Alarm OutputCamera ALC screen Camera Video Adjustment ScreenMode Sense UPMotion ColourArea Edit Colour ModeAlarm Display Home Motion Detect ScreenAuto PAN/PATROL/TRACE Screen Average Peak Iris ModePosition Function SET Screen Position TitleFactory Settings screen Private Mask Setup Repeat steps 5 and 6 for each title character Camera Title SetupTitle from the character area Press the Tele buttonPress the FAR button Area Title SetupDisplay the Setup menu on the camera Move the cursor to Area Title Edit and press the SET buttonTITLE/ALARM menu Alarm Title SetupRepeat steps 5 to 7 for each alarm title TITLE/ALARM screen is displayedArea Edit screen Home Motion Detect SetupMove the cursor to Area Edit and press the SET button Home Motion Detect menuAuto PAN Setup Set the auto pan mode and speedAdjust the viewing angle of the start position Auto Patrol Setup Auto Trace SET screen is displayed Auto Trace SetupMove the cursor to Auto Trace SET and press the SET button Set the patrol start positionPosition Function SET screen Position Title SetupSetup Repeat steps 5 to 7 for each title characterDisplay the Camera FUNCTION2 screen Auto Return SetupDisplay the Setup menu on the camera. P.20, steps 1 to Set the return status using Auto Return functionAttaching a Ceiling Flush Mount Bracket Optional WB-S575 Clamp the Ceiling Flush Mount BracketCeiling plate Connection Cables Attach the Ceiling Mount to the Ceiling Flush Mount BracketAttach the camera to the Ceiling Mount Attach the ceiling panelCheck the release labels thoroughly before removal Removing a Ceiling Flush Mount Bracket Optional WB-S575Remove the ceiling panel Remove the cameraTurned on TroubleshootingSymptom Cause Information Remedy Power cannot beGeneral SpecificationsCamera Pan/Tilt MechanismWB-S575 Ceiling flush mount bracket + Ceiling panel External dimensions Unit mmDimensions in combination with the WB-S575 Ceiling mount holeTK-C655/TK-C676 Dome Type Camera

Related manuals

JVC TK-C676 manual Auto Trace Setup, Move the cursor to Auto Trace SET and press the SET button