JVC GR-DVP3 14 EN, Loading/Unloading a Cassette, Slide the erase protection tab on the back

Page 14

14 EN

Cassette holder cover

Cassette holder

 

Make sure the

 

window side is

 

facing out.

 

PUSH HERE

OPEN/EJECT

Switch

 

Erase protection tab*

*To Protect Valuable Recordings . . .

.... slide the erase protection tab on the back

of the tape in the direction of “SAVE”. This prevents the tape from being recorded over. To record on this tape, slide the tab back to “REC” before loading it.

GETTING STARTED (cont.)

Loading/Unloading A Cassette

The camcorder needs to be powered up to load or eject a cassette.

1 Slide down and hold OPEN/EJECT in the direction of the arrow then pull the cassette holder cover open until it locks. The cassette holder opens automatically.

•Do not touch internal components.

2 Insert or remove a tape and press “PUSH HERE” to close the cassette holder.

•Once the cassette holder is closed, it recedes automatically. Wait until it recedes completely before closing the cassette holder cover.

•When the battery’s charge is low, you may not be able to close the cassette holder cover. Do not apply force. Replace the battery with a fully charged one before continuing.

3 Close the cassette holder cover firmly until it locks into place.

Approximate recording time

Tape

 

Recording mode

 

 

 

SP

 

LP

 

 

30 min.

30 min.

 

45 min.

 

 

 

 

60 min.

60 min.

 

90 min.

 

 

 

 

80 min.

80 min.

 

120 min.

 

 

 

 

Be sure to press only the section labeled

“PUSH HERE” to close the cassette holder; touching other parts may cause your finger to get caught in the cassette holder, resulting in injury or product damage.

NOTES:

It takes a few seconds for the cassette holder to open. Do not apply force.

If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the cassette holder still does not open, turn the camcorder off then on again.

If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again.

When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover.

Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.

Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or unloading.

When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not. See page 22 for information about recording from the middle of a tape.

Image 14
Contents GR-DVP3 Dear Customer It is recommended that youBefore recording an important scene Power Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsProvided Accessories Adjust the length with the adjuster How To Attach The Grip BeltHow To Attach The Strap Remove the pad and separate the two strapsPress + or to select OFF and press SET SelectGetting Started Lithium-ion is vulnerable in colder temperatures PowerCharging the Battery Pack About BatteriesTo Detach The Battery Pack Using the Battery PackUsing AC Power EN1112 EN Grip AdjustmentViewfinder Adjustment Tripod MountingEN13 Date/Time SettingsBuilt-in Clock’s Rechargeable Lithium Battery Slide the erase protection tab on the back 14 ENLoading/Unloading a Cassette Recording Mode Setting EN15To Unload a Memory Card 16 ENLoading a Memory Card EN17 Picture Quality Mode SettingImage Size Mode Setting Approximate Number of Storable ImagesOFF Operation Mode18 EN VideoVideo Recording & Playback Basic Recording To Adjust The Brightness Of The Display20 EN To Stop RecordingInterface Shooting EN21Journalistic Shooting ZoomProper recording When a blank portion is recorded on a tape22 EN Normal Playback To Control The Speaker VolumeAvailable only with the remote control provided  pg EN2324 EN ConnectionsEN25 Docking Station AttachmentBlank Search To cancel Blank Search midway26 EN Press FOCUS/BLANKDigital Still Camera D.S.C Recording Playback Basic Shooting Snapshot Snapshot Mode Selection28 EN Snapshot RecordingTo Remove The Shutter Sound EN29To Delete Unwanted Still Images 30 EN Normal Playback Of ImagesIMAGE/E-CLIP/SOUND Type of File 100-DVC00003 Directory and File namesSelected File Index numberJump Playback 32 ENIndex Playback AgainEN33 To Remove ProtectionTo Select a File by Browsing Files Stored in Memory 34 ENDeleting Files To Delete ALL Files EN35To Delete the Displayed File Before doing the following, perform steps 1 through 3 onTo Print ALL Still Images ONE Print for Each To Reset The Setting36 EN To Print by Selecting Still Images and NO. of Prints To Reset The No. Of PrintsEN37 You can initialize a memory card anytime 38 ENInitializing a Memory Card Advanced Features …see pg For Recording MenuIf you have selected WIPE/FADER Program AE or W. Balance If you have selected Camera MANUAL, SYSTEM, Display or DSCEN41 Menu Screen ExplanationsManual System Wide OFF System Display DSC CAM Cancel EN43For Playback Menu On Next pg EN45Display Sound Mode 12BIT Mode Playback SoundInstead of pressing the Recording Start/Stop Button Second RecordingEN47 Program AE With Special Effects To Deactivate The Selected Mode48 EN Night AliveEN49 FADE/WIPE Selection 50 ENFade/Wipe Effects Menu Effect EN51Fader And Wipe Menu Snapshot For Video Recording Motor Drive Mode52 EN If you press during Record-StandbyEN53 Feature Auto FocusFeature Manual Focus To obtain correct focusIris Lock 54 ENExposure Control EN55 White Balance AdjustmentManual White Balance Operation To Return To Automatic White BalanceDigital Sound Effects Sound Effect Mode Selection56 EN Press + or to select the desired sound effectIng the sound effect EN57Sound Effect Recording 58 EN Dubbing To a VCREN59 To use this camcorder as a player60 EN Dubbing Still Images Recorded On a Tape To a Memory CardEN61 To cancel E-Mail Clip RecordingTape To a Memory Card E-Mail Clip Recording To view video clips stored in a memory cardInstalling The Batteries 62 ENFunctions EN63Buttons Feature Playback Zoom Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback 64 ENFeature Playback Special Effects EN65To hear the dubbed sound during playback 66 ENAudio Dubbing Audio Dubbing Using Digital Sound Effects EN6768 EN Insert EditingEN69 SET REMOTE/VCR CodeMake Connections JVC VCR equipped with a Remote Pause connector70 EN VCR other than aboveEN71 Select Scenes72 EN Automatic Editing to VCREN73 Adjustment of VCR/CAMCORDER TimingFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingUsing USB cable Using USB cableUsing DV cable Using DV cableConnection To a Video Unit Equipped With a DV Connector EN7576 EN References pg PowerEN77 78 EN Corrective ActionEN79 CinemaTroubleshooting 80 ENEN81 VIDEO/MEMORY Switch is 82 ENEN83 After Use Cleaning The Camcorder84 EN Push HereVideo Output Connector Multi ConnectorConnect the editing cable when performing Screw  pg86 EN EN87 Enindex Indications EN89 LCD Monitor/Viewfinder Indications During Video Playback LCD Monitor/Viewfinder Indications During D.S.C. PlaybackEN91 Indications FunctionCard Switch is set to Memory  pgVIDEO/MEMORY Sound is pressed during video recordingEN93 Using Household AC Plug AdapterTemperature Range Specifications 94 EN EN95 96 EN Sound Mode  pg , 44 EN97For Digital Video Camera 98 ENFor General For Digital Still CameraFor Connectors EN99GR-DVP3