JVC GR-SXM730, GR-SXM930 Power, Charging the Battery Pack, To Detach The Battery Pack

Page 8

8 EN

GETTING STARTED

Hook on.

1

2 Push in.

BATTERY RELEASE Switch

REFRESH Button

REFRESH Lamp

CHARGE Lamp

Battery pack

Power Switch

3 To DC IN connector

4

AC Adapter

To AC outlet

Battery pack

Charging time

 

 

BN-V11U

approx. 1 hr. 30 min.

 

 

BN-V12U (optional)

approx. 1 hr. 30 min.

 

 

BN-V20U (optional)

approx. 2 hrs. 20 min.

 

 

BN-V400U (optional)

approx. 4 hrs. 30 min.

 

 

Power

This camcorder’s 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1 Make sure the battery pack is attached to the camcorder. Hook its end to the camcorder 1 and push the battery in until it locks in place 2.

•If the battery pack is attached in the wrong position, a malfunction may occur.

2 Set the Power Switch to “OFF”. Connect the AC Adapter to the camcorder 3.

3 Plug the AC Adapter into an AC outlet 4.

The CHARGE lamp on the camcorder blinks to indicate charging has started.

4 When the CHARGE lamp stops blinking but stays lit, charging is finished. Unplug the AC Adapter from the AC outlet. Disconnect the AC Adapter from the camcorder.

To Detach The Battery Pack . . .

.... slide BATTERY RELEASE and pull out the battery pack.

NOTES:

During charging or discharging, the camcorder cannot be operated.

Charging and discharging is not possible if the wrong type of battery is used.

When charging the battery pack for the first time or after a long storage period, the CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again.

If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

Using the optional AA-V15 AC Power Adapter/Charger, you can charge the BN-V11U/V12U/V20U/V400U battery pack without the camcorder. However, it cannot be used as an AC adapter.

REFRESH:

Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure below to fully discharge the battery pack before recharging.

1.Perform steps 1 through 3 of “CHARGING THE BATTERY PACK”.

2.Press REFRESH on the camcorder for over 2 seconds. The REFRESH lamp on the camcorder blinks to indicate discharging has started.

3.When discharging is finished, charging automatically starts and the CHARGE lamp blinks.

When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing because leaving a battery with some charge left over also reduces performance.

For other notes,  pg. 58

Image 8
Contents GR-SXM930 GR-SXM730 Dear Customer It is recommended that youImportant Safety Instructions Battery Pack Picture Navigator Presto Mr. PhotoPhotoAlbum ImageFolio PC Connection CableHow To Attach The Lens Cap Automatic Demonstration Contents Getting StartedPower Charging the Battery PackTo Detach The Battery Pack Slide Battery Release and pull out the battery packUsing the Battery Pack Using AC PowerPerform of Charging the Battery Pack  pg Approximate recording time unit minGrip Adjustment Viewfinder Adjustment10 EN Shoulder Strap AttachmentDate/Time Settings Appears and then press it. The setting stops blinkingEN11 Press the Menu Wheel in to close the Menu ScreenRecording Format Setting 12 ENEN13 VHS VCR with Sqpb FunctionRegular VHS VCR Sqpb S-VHS Quasi Playback functionRecording Mode Setting Tape Length SettingSet the tape recording mode depending on your preference 14 ENOpen the LCD monitor fully Loading/Unloading a CassetteEN15 Picture Mode Setting 16 ENRETURN. Press the Menu Wheel in to close Menu ScreenContents Video Recording & Playback18 EN Video RecordingTo Stop Recording Rotate the Bright Wheel until the brightSELF-RECORDING EN19Journalistic Shooting Slide the Power Zoom Lever towards T Slide the Power Zoom Lever towards W20 EN ZoomEN21 Set Light OFF/AUTO/ON as required OFF Turns off the light22 EN Video PlaybackTo cancel the effect, select OFF in step EN2324 EN Basic ConnectionsUse optional S-Video and Audio cables Use optional Video and Audio cablesEN25 Power supply instead of the battery pack  pgTape Dubbing 26 EN Video PlaybackDigital Still Camera C. Recording Playback Mode Selection 28 ENC. Recording Still Image StorageEN29 To remove the still image you have checked Instant Delete30 EN C. PlaybackNormal Playback Slide ShowEN31 Index ScreenIndex Playback 32 EN Protecting ImagesTo Protect AN Image To Remove ProtectionTo Delete ALL Images Deleting ImagesEN33 Close the software, then switch off the camcorder 34 ENConnection To a Windows PC During transfer of the still image, the camcorder’sAdvanced Features Advanced FeaturesShutter speed is automatically adjusted maximum 1/6 sec 36 ENNight-Alive Night AutoFade/Wipe Effects EN37Fader Fades in/out to a black screen38 EN Program AE With Special EffectsDigital Effects Press the Menu Wheel in. The normal screen reappears Using Menus For Detailed Adjustment40 EN EN41 Menu Screen ExplanationsCamera Menu System MenuVHS ET 42 ENVHS Snapshot Mode Selection SnapshotEN43 Snapshot Recording44 EN Exposure ControlFocusing EN45Auto Focus Manual FocusWhite Balance Adjustment 46 ENManual White Balance Operation To Return To Automatic White BalanceEN47 Date/Time InsertInstant Titles Time-Lapse 48 ENAnimation Using the Remote Control Unit Functions ButtonsInstalling The Batteries 50 ENEN51 Playback ZoomAnimation And Time-Lapse 52 EN Insert Editing VideoTape Audio DubbingEN53 To insert still images in sequential order onto the tape54 EN ReferencesTroubleshooting 56 EN Never remove the power supply unit at this stage EN57Charging time varies according to the ambient temperature 58 ENTBC indicator turns green gray with a camcorder equipped It may take a few seconds before TBC actually starts working60 EN # $ % 3 4 5 y u 8 9EN61 62 EN Indications During RecordingEN63 Indications During PlaybackTBC Digital Still Camera Contents64 EN Tape Dubbing EN65Store a Still Image In The Built-In Memory 66 EN EN67 Vertically, in their original cases68 EN Specifications EN6970 EN EspañolAlimentación Carga DE LA BateriaAtencion EN71USO DE LA Bateria USO DE Alimentacion CON CAPara extraer la batería 72 ENUtilización de la batería Deslice Battery Release y extraiga la batería Guia Para Operacion Rapida D.S.CUtilización de la batería Para extraer la batería74 EN New Maple Avenue Pine Brook, NJWarranty Only in U.S.A GR-SXM730