JVC GY-DV500 instruction manual VCR Setup Menu Contd, Displaying and Setting VCR Setup Menus

12. SETUP MENU

12-1 VCR Setup Menu (Cont'd)

DISPLAYING AND SETTING VCR SETUP MENUS

CH-1	AUDIO	CH-2	CH-2		TC GENERATOR
	LEVEL	CH-1
		AUTO		PRESET	FREE
		MANUAL		REGEN	REC
		AUDIO SELECT
		AUDIO INPUT					1.
		CH-1	CH-2	CONTINUE		MENU
		FRONT
		REAR
	LITHIUM BATT.	GROUP		ITEM	SELECT	DATA SET
		HOLD		SHIFT	ADVANCE	PRESET	6.
POWER		2.	4.		3. 5.

"MENU" indication

12. SETUP MENU

12-1 VCR Setup Menu (Cont'd)

VCR SETUP MENU CONTENTS

			Item			Setting			Factory
						Value
Group								Contents	Setting
		Upper row: Viewfinder display
		Lower row: Counter display indication
SERVO	050: REMOTE SELECT					LOCAL		Selection of the method for remote control of the VCR. LOCAL
/SYSTEM					IEEE1394			LOCAL : Choose this setting when the VCR should
						RS232C		be controlled using the operation buttons
								on the GY-DV500 only.
							Lc
	rnSL							IEEE1394 : Choose this setting when the VCR should
							IE	be remote controlled from a DV connector
				23				equipped video component connected to
								the DV connector on the rear section of the
								GY-DV500.
								RS232C : Choose this setting for control by means of
								the VCR remote control signal from the VTR

Viewfinder			Viewfinder
	0 0 0	: SERVO / SYSTEM		0 0 0	: SERVO / SYSTEM
	1 0 0	: V I DEO		2 0 0	: AUD I O
	2 0 0	: AUD I O		3 0 0	: SYSTEM
	3 0 0	: SYSTEM		5 0 0	: ON SCREEN
	4 0 0	: T I ME CODE		HM	: HOUR METER
	5 0 0	: ON SCREEN
	HM	: HOUR METER
GROUP menu screen for U-ver.			GROUP menu screen for E-ver.

Counter display

2 4 4 : LOW CUT

OF F

2 4 5 : SAMP L E RATE

4 8 K

2 4 6 : FRONT VOLUME

ENAB L E

Item menu screen

DATA SET

DATA SET display

1. Engaging the VCR Setup Menu mode. Press the MENU button.

•The "MENU" indication in the display section starts blinking and the VCR Setup Menu appears in the viewfinder and on the counter display.

Note:

When a cable is connected to the VTR REMOTE connector, the VTR Setup Menu is not displayed in the viewfinder.

2. Selecting the GROUP. Press the GROUP button.

•Each time the GROUP button is pressed the selected GROUP number is shown blinking on the viewfinder screen. The counter display shows the selected group.

3.Open the Item menu of the selected GROUP. Press the SELECT button.

4.Selecting the Item. Press the ITEM button.

•Each time the ITEM button is pressed the selected item number is shown blinking on the viewfinder screen. The counter display shows the selected item.

5.Changing the setting value of the item.

Press the SELECT button and select the setting value.

When multiple items should be set, repeat the operations of steps 4. and 5.

To set menu items in other groups, press the MENU button. When the relevant group menu is displayed, perform the setting.

When the GROUP button is pressed, the items of the higher order group menu are displayed.

6.Saving the setting value. Press the DATA SET button.

•"DATA SET" appears in the viewfinder and on the counter display and the setting value is saved in the GY-DV500's

memory. The display returns to the normal screen mode when data has been saved.

If the MENU button is pressed without pressing the DATA SET button, the display returns to the normal screen mode without the setting value being changed.

								REMOTE connector on the GY-DV500.
							* The operation buttons on the GY-DV500 remain
							effective even when set to IEEE1394 or RS232C.
	082: BACK TALLY MODE				OFF		Selection of the lighting pattern of the BACK TALLY lamp		BLINK
						ON	on the rear section during recording.
				BLINK			OFF	: The lamp is always off.
							ON	: The lamp lights during recording. It remains
						oF
	rtMd							off until the VTR trigger button is pressed
						on		to start the recording.
						bL	BLINK	: The lamp lights during recording. It blinks
								when the VTR trigger button is pressed to
								start the recording.
VIDEO	126: INPUT SELECT			CAMERA			Selection of the input video signal.		CAMERA
(U-ver. only)				IEEE1394			Settings cannot be changed during recording.
							CAMERA : Camera image is input.
						cA
	vld						IEEE1394 : The image from the DV connector equipped
				IEEE1394				video component connected to the DV
								connector on the rear section is input.
AUDIO	244: LOW CUT				OFF		To select whether or not the low frequencies of the audio		OFF
					CH1		signal from the audio input connectors are cut. Set to
					CH2		ON to reduce the wind noise of the microphone.
				CH1 &			OFF	: The CH1 and CH2 low frequencies are not cut.
					CH2		CH1	: Only the low frequencies of the audio signal
								input to the CH1 channel are cut.
	LctF
						oF	CH2	: Only the low frequencies of the audio signal
			01					input to the CH2 channel are cut.
			02				CH1& CH2 :The low frequencies are cut for both CH1
						on		and CH2.
	245: SAMPLING RATE					32K	To select the sampling rate for digital PCM audio recording.		48K
						48K	32K	: Digital recording occurs with 12-bit, 32 kHz
								sampling
	snPL		32				48K	: Digital recording occurs with 16-bit 48 kHz
			48					sampling.
							* The DV format offers recording tracks for up to 4
							channel when recording using 12-bit, 32 kHz
							sampling. The GY-DV500 records two of these tracks.
							The GY-DV500 does not allow after-recording.
	246: FRONT VOLUME			DISABLE			To select whether or not the front section recording level		ENABLE
		ENABLE		ENABLE			control should be operative. The front section recording
							level control only affects the audio signal recorded on CH1.
							DISABLE : Use of the front section recording level
	FruL
						oF		control is disabled.
						on	ENABLE	: Use of the front section recording level
								control is enabled.
							* The CH-1 recording level control on the side section
							works regardless of the setting.

67

68