Lens optional, Inch Viewfinder optional, VF-P115B

2. CONTROLS, INDICATORS AND CONNECTORS

2-7 Lens (optional)

[S14 x 7.3B12]

7 IRIS mode switch

2. CONTROLS, INDICATORS AND CONNECTORS

2-8 1.5-Inch Viewfinder (optional)

[VF-P115B]

1 Stopper screw

e w	q	A: Activates the auto iris feature.
e w	q	M: Allows manual iris control.
		M: Allows manual iris control.
		8 Momentary auto iris button

This screw prevents the viewfinder from coming off the camera.

2 Mounting guide

	RET	M
		A
	W	T
r	t	y u i o

When the IRIS MODE switch 7 is at "M", pushing this button activates the Auto Iris Function while it is held down only.

9[S] IRIS speed adjusting control

For adjusting the iris operation speed.

Memo:

If the speed becomes too fast, hunting may occur.

•To avoid the phenomena described above, perform adjustment again.

0FILTER thread

Protect the lens with a clear filter or UV filter by screwing the filter onto the thread inside the lens hood from the front. Other filters can be used for various effects.

CAUTION:

	1
4	2
5	3

To attach on the camera.

3Connector

Connect to the camera.

4[CONT] contrast adjustment

To adjust the contours of the viewfinder image.

5[BRIGHT] brightness adjustment

To adjust the brightness of the viewfinder.

6[TALLY] switch

Set this switch to OFF to prevent the tally light 7 from turning on and informing people that they are being recorded. However, the REC indicator lamp in the eyepiece will not turn off.

The filter thread section rotates, so pay attention when mounting a polarizing filter.

7 Tally light

Lights when recording is in progress. To prevent this light from coming on, set the tally switch 6 to "OFF".

!0!4

!ZOOM servo connector

Connect an optional zoom servo unit here.

8 Eyepiece

Ensures that ambient light does not reach the viewfinder

1 FOCUS ring Manual focus ring.

MACRO

!1 !2 !3

@ZOOM mode knob

S:Servo zoom mode. Allows operation by the zoom servo

control lever 6.

M:Manual zoom mode. Allows zoom control by the zoom lever/ring 2.

#BACK FOCUS ring/fixing screw

For back focus adjustment only. Secure with the screw knob after adjustment.

☞ See “Back Focus Adjustment” on page 44.

$ Macro focusing ring (for close-up shooting)

By rotating this ring in the direction of the arrow, close-up

screen or falls into the eye of the cameraman.

The eyepiece can be opened to allow direct observation of the viewfinder screen.

9 Eyepiece focusing ring

Loosen this ring to move the eyepiece back or forth to adjust the diopter.

2ZOOM lever/ring

This is the manual zoom ring equipped with a zoom lever. To adjust the zoom manually, turn the zoom mode knob @ to position "M".

3IRIS ring

Manual iris ring. To activate the auto iris feature, set the Iris Mode switch 7 to A.

4[VTR] Trigger button

To start/stop shooting.

5[RET] return video button

The return video signal from the VCR section can be monitored in the viewfinder only while this button is pushed.

*The playback picture can be viewed in the viewfinder during this operation.

6ZOOM servo control lever

To operate the servo zoom feature with this lever, set the ZOOM knob @ to S.

•Pressing the W section of this lever increases the angle of the lens for a wider shooting angle.

•Pressing the T section of this lever narrows the lens angle perspective for telephoto shots.

•Pushing harder changes the speed of the zoom.

shooting of very small objects becomes possible.

Normal focus adjustment and zooming are not available in

the macro mode.

To shoot images in the macro mode, set the focus ring 1 to

the infinite position and the zoom ring 2 to the maximum

wide-angle position. To adjust the focus of the macro image,

rotate this ring in the direction of the arrow until the object

is focused.