Panasonic AJ-HD1700 manual Edit

Setup menus

<EDIT>

No./Item

Description of setting

300

For selecting the operation to be performed when

an edit point has been set incorrectly (when the

IN/OUT DEL

OUT point comes before the IN point).

0000

MANU

:

Editing is not performed unless the illegal edit

point is cleared or set properly.

0001

AUTO

:

The edit point which had already been input is

cleared automatically.

301

For selecting whether to show a negative display

(time code display area) when the IN point is

NEGA FLASH

greater than the OUT point.

0000

OFF

:

A negative display is not shown.

0001

ON

:

A negative display is shown.

302

For selecting whether to perform simultaneous

playback during editing.

CONFI EDIT

0000

OFF

:

Simultaneous playback is

not

performed.

0001

ON

:

Simultaneous

playback

is

performed.

<Note>

Simultaneous playback takes effect when TAPE is

selected as the F1 key

on

the

OUTPUTsetting

<HOME> menu. Refer to setup menu item No.140 as

well.

1

For selecting how to connect the digital audio

303*

edit IN points.

AUD EDIT

0000

CUT

:

Cut processing

IN

0001

FADE

:

V-fade processing

304*1

For selecting how to connect the digital audio

edit OUT points.

AUD EDIT

0000

CUT

:

Cut processing

OUT

0001

FADE

:

V-fade processing

305

For selecting whether to register the IN points

using the PREROLL button in cases where

AUTO ENTRY

the IN points have not been registered.

0000

DIS

:

The

IN

points

are

not

registered.

0001

ENA

:

The IN points are registered.

1

For selecting the deck whose the color

306*

framing is to be adjusted during deck-to-deck

CF ADJ SEL

editing.

0000

PLAYER

:

The player’s IN and OUT points are adjusted

(using the recorder as the reference).

0001 RECORD

:

The recorder’s IN and OUT points are adjusted

(using the player as the reference).

307

For

selecting

the

VTR’s

mode

upon

completion of the cue-up operation.

AFTER

0000

STOP

:

CUE-UP

The VTR is set to the STOP mode.

0001

STILL

:

The VTR is set to the still picture (SHTL STILL)

mode.

0002

STILL2

:

The VTR is set to the still picture (VAR STILL)

mode.

No./Item			Description of setting
308	For setting the maximum speed of VAR FWD.
		0000	i4.9:	i4.9 times normal tape speed
VAR FWD	0001		i2:	i2 times	normal	tape speed
MAX				(i1.85	times	normal	tape
				speed for formats other than
				DVCPRO HD-LP)
	0002		i1:	i1 times normal tape speed
	<Notes>
	• At any setting other than 0 (				i4.9), phase adjustments
		cannot be conducted from the editing controller.
	• Depending		on the format used, the actual tape
		running speed differs slightly from what is indicated
		by the superimposed display.
309	For setting the maximum speed of VAR REV.
		0000	j4.9:	j4.9 times normal tape speed
VAR REV MAX	0001		j2:	j2 times	normal	tape speed
				(j1.85	times	normal	tape
				speed for formats other than
				DVCPRO HD-LP)
	0002		j1:	j1 times normal tape speed
	<Note>
	Depending on the format used, the actual tape running
	speed differs slightly from what is indicated by the
	superimposed display			.
310	For setting the maximum speed of JOG FWD.
	0000		i4.9:	i4.9 times normal tape speed
JOG FWD	0001		i2:	i2 times	normal	tape speed
MAX				(i1.85	times	normal	tape
				speed for formats other than
				DVCPRO HD-LP)
		0002	i1:	i1 times normal tape speed
	<Notes>
	At any setting other than 0 (				i4.9), phase adjustments
	cannot be conducted from the editing controller which
	performs these adjustments by the JOG command.
311	For setting the maximum speed of JOG REV.
	0000		j4.9:	j4.9 times normal tape speed
JOG REV MAX	0001		j2:	j2 times	normal	tape speed
				(j1.85	times	normal	tape
				speed for formats other than
				DVCPRO HD-LP)
	0002		j1:	j1 times normal tape speed
312	For setting the postroll time.
	Any time from 0 to 5 seconds can be set in 1-
POSTROLL	second increments.
TM	0000		0s
	0001		1s
		0002	2s
	0003		3s
	0004		4s
	0005		5s

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

88