Panasonic AJ-HD1700 manual FRZ Mode, Rec Inh, All, Pre, Norm, Lamp, Eject SW, Off

Setup menus

<OPERATION>			(continued)
No./Item					Description of setting
112	For selecting what playback images are to be
	output in the STANDBY OFF mode and EJECT
FRZ MODE	mode.
SEL	0000			DIS		:
		The video output is muted.
	0001 STB OFF					:
		Only when the STANDBY OFF mode is
		established			is	the	image which was being
		played back at that moment frozen and output.
	0002 SOF&EJ					:
		When either the STANDBY OFF mode or the
		EJECT mode is established, the image which
		was being		played back at that moment is
		frozen and output.
	<Notes>
	• The status when the picture is frozen is determined
		by the setup menu item No.604 (FREEZE SEL)
		setting.
	• In the EJECT mode, the frozen picture is output only
		when 1 (BLACK) or 2 (GRAY) has been selected as
		the setup menu				item	No.106 (EJECT EE SEL)
		setting.
	• The picture freeze is forcibly released if a change has
		occurred in the output format of the HD serial output
		signals when operation has transferred to the EJECT
		mode.
Description of MEMORY STOP function
							The MEMORY STOP function does
							not work if this margin is less than
	0			point			d2 frames.

3 REW	1 FF
button	button
4 FF	2 REW
button	button

!If the FF button is pressed, the normal FF operation is performed since there is no 0 point in the direction of this operation.

@If the REW button is pressed, the PREROLL lamp lights (as does the SHTL lamp), the VTR prerolls the tape, and it automatically stops when the counter value is at the 0 position.

#If the REW button is pressed, the normal REW operation is performed since there is no 0 point in the direction of this operation.

$If the FF button is pressed, the PREROLL lamp lights (as does the SHTL lamp), the VTR prerolls the tape, and it automatically stops when the counter value is at the 0 position.

No./Item					Description of setting
113*	For selecting whether to allow or inhibit recording
	on the cassette tape.
REC INH		0000			OFF	:
		Recording on the cassette tape is enabled when the
		cassette’s accidental erasure prevention mechanism
		has been set to the recording enable position.
	0001			ALL		:
		All recording on the cassette tape is inhibited.
	0002			PRE		:
		Overwriting is inhibited during normal recording.
		This is the setting to activate the accidental erasure
		prevention function. While CTL is detected, the
		recording is inhibited, and when CTL cannot be
		detected, it is executed.
	0003		NORM			:
		Normal recording is inhibited.
		Use this setting when it is preferable to avoid
		using	normal recording in all applications
		except for editing.
	0004		V/CTL			:
		The recording of the video and CTL signals is
		inhibited.
		Use this setting when it is preferable to avoid editing
		in all applications except for audio editing						.
	<Note>
	When the PRE, NORM or V/CTL setting has been
	selected, the REC INHIBIT lamp blinks (on for approx.
	0.5 sec. and then off for approx. 0.5 sec.).
114	For selecting whether the REC INHIBIT lamp is to
	blink or light when the cassette tape has been set
REC INH	to the accidental erasure protection mode.
LAMP		0000	LIGHT			:	The lamp lights.
		0001	FLASH			:	The lamp blinks.
	<Note>
	If 1 (ALL) has been selected as the setup menu item
	No.113 (REC INH) setting, the REC INHIBIT lamp will
	be lighted at all times regardless of the REC INH LAMP
	setting.
115*	For selecting whether to enable or disable the
	operation of the EJECT button on the VTR’s
EJECT SW	front panel.
INH		0000			REC	: Operation is disabled while the
							VTR is in the recording mode.
	0001			OFF		:	Operation is enabled in	all
							modes.

Accidental erasure protection function

This function is used to prevent parts already recorded on a tape from being recorded over. Accidental erasure of pre-recorded tapes is prevented by positioning the CTL signal rec/play heads as shown in the figure below so that whether a recording has been made can be determined by the presence or absence of the CTL signal. When the REC/PLAY button is pressed with a pre- recorded tape, the tape runs but the REC button lamp blinks, the beeping alarm is sounded, and no signals are recorded.

A/C heads (rec/play heads)

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or SD) mode has been selected as the system menu item No.25 (SYSTEM FREQ) setting.

The underlining (__) denotes the factory setting mode.

PRE CTL head

Rough sketch showing CTL head positions

85