Axis Communications Q1614-E user manual UPnPTM, RTP/H.264

Page 55

AXIS Q1614-E Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 48. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 60.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Axis Q1614-E Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q1614-E Network Camera Table of ContentsConnectors Performance Considerations Hardware Overview Axis Q1614-E Network Camera For technical specifications, see Connectors and ButtonsNetwork Connector ConnectorLED Indicators Buzzer Buzzer Signal for Focus AssistantStatus LED Behavior for Focus Assistant ColorColor Buzzer Camera position Replace the LensSet the Root Password Access the ProductAccess from a Browser Access from the InternetLive View PTZ ModeConfigure Capture Mode Set Power Line FrequencyTo show the manual trigger buttons in the Live View Go to Setup EventsControls on the Live View Manual TriggerPTZ Controls Axis Media Control viewer toolbarAMC Audio Controls Axis Q1614-E Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductFocus Adjustment Image Video and AudioVideo Stream Pixel CounterStream Profiles Click Save to apply the new settings264 Capture Mode Camera SettingsGo to Setup Video & Audio Camera Settings White Balance Lightfinder ModeExposure Settings Image AppearanceDay/Night Iris configurationIris adjustment Set Shutter toGo to Video & Audio Video Stream and select the Image tab To configure the view areaView Area OverlayUse Overlay Text in an Action Rule Overlay ImageGo to Video & Audio Overlay Image Basic Privacy MaskFocus Go to Events Action RulesAudio Modes Audio SettingsAudio Input Audio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGuard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControl Queue Install PTZ DriverDevice Settings AdvancedOperator Same as administrator but with lower priority Shock Detection DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q1614-E Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersActions Go to Events Recipients and click Add Set Up Email RecipientsAdd Recipients PTZ ControlGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsFind Recordings Play RecordingGo to Recordings Continuous Export Video ClipContinuous Recording To play a recording, follow these stepsLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 Mount and Unmount SD Card StorageBonjour SD CardGo to System Options Storage Click Network Share Under General Settings, select Autoformat toNetwork Share To add a network sharePorts & Devices MaintenanceLogs & Reports SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserSetup Video & Audio Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Network Security Function/group Specifications Audio Audio streamingAudio input Audio outputDimensions Function/group SpecificationsPower ConnectorsConnectors Function Pin RS485/422 ConnectorPerformance Considerations OutputAxis Q1614-E Network Camera M5.5
Top Page Image Contents