Axis Communications P5522 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 43

AXIS P5522 PTZ Dome Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 37. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 46.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are conﬁgured under System Options > Network > RTP.

The RTP port range deﬁnes the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

The SD/SDHC memory card (not included) is managed on the System Options > Storage > SD Card page.

The settings under Storage Device are used to identify and monitor the status of the SD card, and to unmount the SD card before removal. Mounting is done automatically when a card is inserted. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair.

The settings under Storage Device Settings are used to conﬁgure removal of recorded video. Automatic disk cleanup can be enabled and set according to a schedule. The disk can be locked to prevent removal of recordings.

For more information, see the online help.

43

Image 43

Contents Axis P5522 PTZ Dome Network Camera Equipment Modiﬁcations About this documentLiability Intellectual Property RightsAxis P5522 PTZ Dome Network Camera Table of contentsHardware overview ConnectorsHardware overview Color Indication LED indicatorsStart a browser Internet Explorer, Firefox, Safari Accessing the productAccessing the product Access from a browserClick Create self-signed certiﬁcate Access from the InternetSet the root password Network TCP/IP AdvancedControls on the Live View Live ViewAxis Media Control viewer toolbar AMC Audio controls PTZ ControlsAxis P5522 PTZ Dome Network Camera Axis Media Control AMC How to stream H.264Media streams Media streamsQuickTimeTM. The following paths can be used Alternative methods of accessing the video streamJava applet supports simplex audio with G.711 encoding Accessing audio streamsSetting up the product Setting up the productBasic Setup Image Video and AudioVideo and Audio Video StreamImage Appearance Camera SettingsStream Proﬁles 264Wide Dynamic Range Exposure SettingsImage settings White balanceOverlay image Audio SettingsOverlay Privacy MaskAudio Output Audio InputAudio Clips Live View Conﬁg Default viewer for browsersLive View Conﬁg Browser Viewer Description Viewer SettingsUser Deﬁned Links Output ButtonsAxis P5522 PTZ Dome Network Camera Guard Tour Preset positionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomGo to PTZ Guard Tour and click Add Osdi ZonesAdvanced LimitsSee the online help for more information Operator Same as administrator but with lower priorityControl Queue ControlsApplications ApplicationsServer type Purpose Information required EventsEvents Event ServersEvent Types Set up a triggered eventGo to Events Event Types and click Add triggered Save stream Set up a scheduled eventGo to Events Event Types and click Add scheduled Go to Events Motion Detection Set up motion detectionGatekeeper Motion detectionMotion detection parameters Port Status Audio detectionGo to Events Audio Detection Recordings RecordingsEvent recordings Go to Recordings Continuous Continuous recordingAxis P5522 PTZ Dome Network Camera System Options System OptionsSecurity Audio Support Date & TimeNetwork Basic TCP/IP SettingsNTP Conﬁguration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConﬁgurationNAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Ports & Devices MaintenanceSupport File Upload ScriptingPlain Conﬁg Reset to factory default settingsMulti-Connector Cable sold separately Multi-Connector Cable sold separatelyFunction Pin Speciﬁcations Connector DC power input Connection diagramChecking the ﬁrmware TroubleshootingTroubleshooting Emergency recovery procedureProduct is accessible locally but not externally Symptoms, possible causes and remedial actionsProblems setting the IP address Camera cannot be accessed from a browserKey frames Problems with the H.264 formatVideo and image problems, general Video & Audio Camera SettingsOverlay image is not displayed Problems uploading ﬁlesSettings Storage and disk management problemsTechnical Speciﬁcations Technical SpeciﬁcationsMaintenance General Casing Alarm triggersAlarm events InstallationPerformance considerations M2.4

Related manuals

Manual 66 pages 12.29 Kb