Axis Communications Q6045-E user manual Midspan LED Indicators, SD Card Slot, Control Button

Page 7

AXIS Q6045-E PTZ Dome Network Camera

Hardware Overview

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the midspan shall be shielded (STP) and intended for their specific use. Make sure that the midspan is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .

To comply with the IP66-rated design of the camera and maintain the IP66 protection, the supplied RJ45 Push-pull Connector (IP66) shall be used. Alternatively, use the RJ45 IP66-rated cable with premounted connector which is available from your Axis reseller. Do not remove the plastic network connector shield from the camera.

SD Card Slot

An SD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Control Button

The control button is used for:

Resetting the product to factory default settings. See page 52.

Connecting to an AXIS Video Hosting System service. See page 46. To connect, press and hold the button for about 1 second until the Status LED flashes green.

Connecting to AXIS Internet Dynamic DNS Service. See page 46. To connect, press and hold the button for about 3 seconds.

Power Button

Press and hold the power button to temporarily power the product when the dome cover is removed. The power button is also used with the control button to reset the camera to factory default settings. See page 52.

LED Indicators

LED

Color

Indication

 

 

 

Status

Unlit

Connection and normal operation

 

 

 

 

Amber

Steady during startup. Flashes during firmware upgrade.

 

 

 

 

Amber/red

Flashes amber/red if network connection is unavailable or lost.

 

 

 

 

Red

Flashes red for firmware upgrade failure.

 

 

 

 

Green

Shows steady green for 10 seconds for normal operation after restart.

 

 

 

Midspan LED Indicators

LED

Color

Indication

 

 

 

Port

Unlit

No camera connected.

 

 

 

 

Green

Steady when camera connected, normal operation.

 

 

 

 

Green, flashing

Slow flash when overcurrent or short circuit condition on the port.

 

 

 

 

Green, flashing

Fast flash when input voltage is out of range or other internal error.

 

 

 

AC

Green

Steady when AC power input connected.

 

 

 

7

Image 7
Contents Axis Q6045-E PTZ Dome Network Camera Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis Q6045-E PTZ Dome Network Camera Table of ContentsTechnical Specifications Hardware Overview Connectors and ButtonsNetwork Connector Hardware OverviewSD Card Slot LED IndicatorsMidspan LED Indicators Power ButtonAccessing the Product Accessing the ProductAccess from a Browser Click Use Https Accessing the Product Access from the InternetSet the Root Password Network TCP/IP AdvancedManual Trigger Accessing the Product Live ViewGo to Setup Events Controls on the Live ViewPTZ Controls Axis Media Control viewer toolbarAxis Q6045-E PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsAlternative Methods of Accessing the Video Stream Axis Q6045-E PTZ Dome Network Camera Setting Up the Product Setting Up the ProductBasic Setup Pixel Counter VideoVideo Video StreamImage Stream Profiles264 White Balance Camera SettingsExposure Settings Image AppearanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Overlay ImagePrivacy Mask Using Overlay Text in an Action RuleGo to Events Action Rules Axis Q6045-E PTZ Dome Network Camera Live View Config Live View ConfigDefault Viewer for Browsers User Defined Links Viewer SettingsBrowser Viewer Description PTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomMax Limits ConfigurationPTZ Pan Tilt Zoom Autotracking Exclude AreasGuard Tour GatekeeperLimits Osdi ZonesAdvanced Tour RecordingControls Control QueueShock Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Object RemovedFence Detector Enter/Exit DetectorObject Counter Application Licenses Install ApplicationApplications ApplicationsAxis Q6045-E PTZ Dome Network Camera Detectors Input SignalEvents EventsTime Setting Up an Action RuleStorage SystemRecipient RecipientsFallback Action Go to Events Action Rules and click AddGo to Events Schedules and click Add Setting Up an Email RecipientSchedules Go to Events Recipients and click AddGo to Events Recurrences and click Add RecurrencesContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityCertificates IeeeGo to System Options Security Ieee Go to System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Assign IP Address Using ARP/PingNTP Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address Host Name ConfigurationNAT traversal port mapping for IPv4 Smtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage and click SD Card Network ShareGo to System Options Storage Click Network Share System Overview System Options MaintenanceSupport Support OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis Q6045-E PTZ Dome Network Camera Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Key frames Video and image problems, generalVideo Camera Settings Storage and disk management problemsTechnical Specifications Technical SpecificationsPower Function/group Specifications System ApplicationInstallation aid MaintenancePerformance Considerations M2.2
Related manuals
Manual 65 pages 47.07 Kb Manual 24 pages 14.82 Kb

Q6045-E specifications

Axis Communications Q6045-E is an advanced network camera designed specifically for professional surveillance applications. This camera exemplifies Axis's commitment to high-performance video surveillance solutions, combining cutting-edge technology with robust design features.

One of the standout characteristics of the Q6045-E is its exceptional imaging capabilities. Equipped with a 1/2.8” sensor, it delivers high-resolution video at up to 1080p, ensuring clear and detailed images even in challenging lighting conditions. The camera supports a wide dynamic range (WDR), enabling it to capture high-quality images in environments with varying light levels, such as areas that experience both bright sunlight and deep shadows.

The Q6045-E also integrates a powerful 30x optical zoom lens, which allows for detailed close-ups of objects at a distance. This feature is essential for applications requiring precise identification, such as monitoring perimeters, parking lots, and business premises. The camera includes intelligent video analytics capabilities, providing features like motion detection, tampering alarm, and audio detection, enhancing the effectiveness of security measures.

Another noteworthy aspect is the camera’s PTZ (pan-tilt-zoom) functionality. It can pan 360 degrees and tilt from -20 to 90 degrees, providing extensive coverage and flexibility for optimal surveillance. This means a single Q6045-E can monitor vast areas, reducing the need for multiple cameras and thus lowering overall system costs.

Durability and reliability are also key features of the Q6045-E. Designed for outdoor use, the camera is IP66-rated and NEMA 4X-rated, which means it can withstand harsh weather conditions, including rain, snow, and extreme temperatures. The built-in heater ensures consistent performance in cold environments, maintaining both functionality and image quality.

The camera is powered over Ethernet (PoE), facilitating easy installation with just one cable for both data and power. This simplifies the setup process and reduces additional wiring costs. Additionally, the Q6045-E supports various video compression formats, including H.264 and H.265, allowing for efficient bandwidth usage without compromising video quality.

In conclusion, Axis Communications Q6045-E is a feature-rich choice for any professional surveillance system, offering high-resolution video, intelligent analytics, robust durability, and flexible installation options. Its innovative technologies make it an ideal solution for enhancing security and surveillance efforts in a wide range of environments.