Axis Communications P5522 user manual Network, Basic TCP/IP Settings

Page 47

AXIS P5522 PTZ Dome Network Camera

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 55) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 47.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Axis P5522 PTZ Dome Network Camera Equipment Modifications About this document Legal ConsiderationsLiability Intellectual Property RightsLearn More SupportAxis P5522 PTZ Dome Network Camera Table of ContentsPerformance Considerations Support Advanced Reset to Factory Default SettingsOther Message Levels Safety InformationHazard Levels Hardware Overview For technical specifications, see Connectors and ButtonsNetwork Connector Multi-connectorControl Button LED IndicatorsMidspan LED Indicators SD Card SlotAccess from the Internet Access the ProductAccess from a Browser Controls on the Live View Set the Root PasswordSet Power Line Frequency Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls PTZ ControlsAxis P5522 PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Set Up Video StreamsVideo and Audio Pixel Counter264 Click Save to apply the new settingsStream Profiles White Balance Camera SettingsExposure Settings Image AppearanceGo to Video & Audio Video Stream and select the Image tab Image SettingsOverlay Go to Video & Audio Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Set Up AudioPrivacy Mask Audio ModesAudio Input Audio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsOutput Buttons Go to Setup Live View ConfigUser Defined Links Gatekeeper Preset PositionsPTZ Pan Tilt Zoom Limits Guard TourOsdi Zones AdvancedControls Control Queue Operator Same as administrator but with lower priorityMotion Detection Parameters Set Up Motion Detection WindowsDetectors Motion DetectionLow level 0% Default valuesAudio Detection Medium level 50%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P5522 PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesActions TriggersGo to Events Recipients and click Add Add RecipientsRecipient Types PTZ ControlGo to Events Schedules and click Add Set Up Email RecipientsCreate Schedules Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P5522 PTZ Dome Network Camera Drain, 100 mA Multi-Connector Cable sold separatelyCable provides the following connectors Function Pin SpecificationsConnector Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Setup Video & Audio Camera SettingsPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Power Function/group Specifications Network SecurityInstallation Maintenance General CasingPerformance Considerations M5.2
Related manuals
Manual 56 pages 25.76 Kb
Top Page Image Contents