Axis Communications P5522 user manual UPnPTM, RTP/H.264, Bonjour

Page 51

AXIS P5522 PTZ Dome Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 44. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 55.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

51

Image 51
Contents Axis P5522 PTZ Dome Network Camera Equipment Modifications About this document Legal ConsiderationsLiability Intellectual Property RightsLearn More SupportAxis P5522 PTZ Dome Network Camera Table of ContentsPerformance Considerations Support Advanced Reset to Factory Default SettingsSafety Information Hazard LevelsOther Message Levels Hardware Overview For technical specifications, see Connectors and ButtonsNetwork Connector Multi-connectorControl Button LED IndicatorsMidspan LED Indicators SD Card SlotAccess the Product Access from a BrowserAccess from the Internet Controls on the Live View Set the Root PasswordSet Power Line Frequency Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls PTZ ControlsAxis P5522 PTZ Dome Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductImage Set Up Video StreamsVideo and Audio Pixel CounterClick Save to apply the new settings Stream Profiles264 White Balance Camera SettingsExposure Settings Image AppearanceImage Settings OverlayGo to Video & Audio Video Stream and select the Image tab Overlay Image Use Overlay Text in an Action RuleGo to Video & Audio Overlay Image Go to Events Action Rules Set Up AudioPrivacy Mask Audio ModesAudio Input Audio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsGo to Setup Live View Config User Defined LinksOutput Buttons Preset Positions PTZ Pan Tilt ZoomGatekeeper Limits Guard TourOsdi Zones AdvancedControls Control Queue Operator Same as administrator but with lower priorityMotion Detection Parameters Set Up Motion Detection WindowsDetectors Motion DetectionLow level 0% Default valuesAudio Detection Medium level 50%Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis P5522 PTZ Dome Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesActions TriggersGo to Events Recipients and click Add Add RecipientsRecipient Types PTZ ControlSet Up Email Recipients Create SchedulesGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingLanguages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardPorts MaintenancePorts & Devices Network ShareLogs & Reports SupportSupport Overview System OverviewFile Upload Reset to Factory Default SettingsPlain Config ScriptingAxis P5522 PTZ Dome Network Camera Drain, 100 mA Multi-Connector Cable sold separatelyCable provides the following connectors Function Pin SpecificationsConnector Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserKey frames Problems with streaming H.264Video and image problems, general Setup Video & Audio Camera SettingsPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Power Function/group Specifications Network SecurityInstallation Maintenance General CasingPerformance Considerations M5.2
Related manuals
Manual 56 pages 25.76 Kb