Axis Communications P3384VE Set Up Action Rules, Go to Events Action Rules and click Add

Page 36

AXIS P3384–VE Fixed Dome

Events

Events

The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.

Set Up Action Rules

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send an email notification. If multiple conditions are defined, all of them must be met to trigger the action.

For more information about available triggers and actions, see Triggers on page 37 and Actions on page 38.

The following example describes how to set up an action rule to record video to a network share if there is movement in the camera’s field of view.

Set up motion detection and add a network share:

1.Go to Detectors > Motion Detection and configure a motion detection window. See page 32

2.Go to System Options > Storage and set up the network share. See page 55.

Set up the action rule:

1.Go to Events > Action Rules and click Add.

2.Select Enable rule and enter a descriptive name for the rule.

3.Select Detectors from the Trigger drop-down list.

4.Select Motion Detection from the drop-down list. Select the motion detection window to use.

5.Optionally, select a Schedule and Additional conditions. See below.

6.Under Actions, select Record Video from the Type drop-down list.

7.Select a Stream profile and configure the Duration settings as described below.

8.Select Network Share from the Storage drop-down list.

To use more than one trigger for the action rule, select Additional conditions and click Add to add additional triggers. When using additional conditions, all conditions must be met to trigger the action.

To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated again.

The recording Duration of some actions can be set to include time immediately before and after the event. Select Pre-trigger time and/or Post-trigger time and enter the number of seconds. When While the rule is active is enabled and the action is triggered again during the post-trigger time, the recording time will be extended with another post-trigger time period.

For more information, see the online help .

Set Up Action Rules

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send an email notification. If multiple conditions are defined, all of them must be met to trigger the action.

For more information about available triggers and actions, see Triggers on page 37 and Actions on page 38.

36

Image 36
Contents Axis P3384-VE Fixed Dome About this Document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3384-VE Fixed DomeAdvanced Reset to Factory Default Settings Connectors Performance ConsiderationsHardware Overview Connectors and Buttons LED Indicators Color IndicationAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordSet Power Line Frequency Live ViewControls on the Live View Click Use HttpsGo to Setup Events Axis Media Control viewer toolbarManual Trigger To show the manual trigger buttons in the Live ViewPTZ Controls AMC Audio ControlsAxis P3384-VE Fixed Dome How to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupClick Save to apply the new settings Video and AudioVideo Stream ImageStream Profiles MjpegCamera Settings Lightfinder ModeImage Appearance White BalanceExposure Settings Iris adjustmentShutter & Gain Set Shutter toSelect an Aspect ratio and a Video stream resolution View AreaOverlay Go to Video & Audio View AreaPrivacy Mask Overlay ImageGo to Video & Audio Overlay Image Audio Settings When satisfied, click Enable iris to enable the irisFocus & Zoom Audio ModesAudio Input Audio Clips Audio OutputConfigure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionGo to Setup Live View Config User Defined LinksOutput Buttons For more information about I/O ports, see I/O Ports onPreset Positions PTZ Pan Tilt ZoomGuard Tour AdvancedOperator Same as administrator but with lower priority Control QueueDetectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAudio Detection Go to Detectors Audio DetectionInstall Application Go to Setup ApplicationsApplications Application LicensesAxis P3384-VE Fixed Dome Set Up Action Rules EventsGo to Events Action Rules and click Add For more information, see the online helpTriggers DetectorsHardware Actions Add Recipients Recipient TypesGo to Events Recipients and click Add Recipient Use with actionSet Up Recurrences Set Up Email RecipientsCreate Schedules Go to Events Schedules and click AddAxis P3384-VE Fixed Dome Recordings Find RecordingsPlay Recording Go to Recordings ListExport Video Clip Recording ListContinuous Recording Go to Recordings ContinuousLanguages System Options SecurityUsers IP Address FilterIeee CertificatesCA Certificate Go to Setup System Options Security Certificates Click Install certificate and upload the certificateDate & Time CertificatesBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service Linux/Unix syntaxLinux/Unix example Axis Video Hosting System AvhsAdvanced TCP/IP Settings DNS ConfigurationNTP Configuration Host Name ConfigurationHttps NAT traversal port mapping for IPv4QoS Quality of Service SocksStorage UPnPTMRTP/H.264 BonjourNetwork Share Mount and Unmount SD CardFormat SD Card To add a network shareMaintenance Ports & DevicesPorts Port StatusSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigFile Upload Troubleshooting Upgrade the FirmwareFirmware To upgrade the product’s firmware Check the FirmwareEmergency Recovery Procedure Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserProduct is accessible locally but not externally Problems with streaming H.264Basic Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings SettingsVideo cannot be recorded Technical Specifications Function/group Specifications Network Security InstallationMaintenance SupportedFunction/group Specifications General Casing PowerConnectors DimensionsConnectors Function Pin SpecificationsPerformance Considerations Audio InputAudio Output M3.11