Axis Communications P3384VE user manual Socks, QoS Quality of Service

Page 53

AXIS P3384–VE Fixed Dome

System Options

SOCKS

SOCKS is a networking proxy protocol. The Axis product can be configured to use a SOCKS server to reach networks on the other side of a firewall or proxy server. This functionality is useful if the Axis product is located on a local network behind a firewall, and notifications, uploads, alarms, etc need to be sent to a destination outside the local network (for example the Internet).

SOCKS is configured under System Options > Network > SOCKS. For more information, see the online help .

QoS (Quality of Service)

QoS (Quality of Service) guarantees a certain level of a specified resource to selected traffic on a network. A QoS-aware network prioritizes network traffic and provides a greater network reliability by controlling the amount of bandwidth an application may use.

The QoS settings are configured under System Options > Network > QoS. Using DSCP (Differentiated Services Codepoint) values, the Axis product can mark different types of traffic.

Note

Live audio DSCP will be equal to live video DSCP if H.264 over RTSP is used.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 46. To enable SNMP v3, check the box and provide the initial user password.

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Axis P3384-VE Fixed Dome Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis P3384-VE Fixed Dome Table of ContentsConnectors Performance Considerations Advanced Reset to Factory Default SettingsHardware Overview Connectors and Buttons Color Indication LED IndicatorsAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordLive View Set Power Line FrequencyControls on the Live View Click Use HttpsAxis Media Control viewer toolbar Go to Setup EventsManual Trigger To show the manual trigger buttons in the Live ViewAMC Audio Controls PTZ ControlsAxis P3384-VE Fixed Dome Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductVideo and Audio Click Save to apply the new settingsVideo Stream ImageMjpeg Stream ProfilesLightfinder Mode Camera SettingsImage Appearance White BalanceIris adjustment Exposure SettingsShutter & Gain Set Shutter toView Area Select an Aspect ratio and a Video stream resolutionOverlay Go to Video & Audio View AreaGo to Video & Audio Overlay Image Privacy MaskOverlay Image When satisfied, click Enable iris to enable the iris Audio SettingsFocus & Zoom Audio ModesAudio Input Audio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Go to Setup Live View ConfigOutput Buttons For more information about I/O ports, see I/O Ports onPTZ Pan Tilt Zoom Preset PositionsGuard Tour AdvancedControl Queue Operator Same as administrator but with lower priorityCamera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsGo to Detectors Audio Detection Audio DetectionGo to Setup Applications Install ApplicationApplications Application LicensesAxis P3384-VE Fixed Dome Events Set Up Action RulesGo to Events Action Rules and click Add For more information, see the online helpHardware TriggersDetectors Actions Recipient Types Add RecipientsGo to Events Recipients and click Add Recipient Use with actionSet Up Email Recipients Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddAxis P3384-VE Fixed Dome Find Recordings RecordingsPlay Recording Go to Recordings ListRecording List Export Video ClipGo to Recordings Continuous Continuous RecordingLanguages Security System OptionsUsers IP Address FilterCA Certificate IeeeCertificates Click Install certificate and upload the certificate Go to Setup System Options Security CertificatesDate & Time CertificatesNetwork Basic TCP/IP SettingsLinux/Unix syntax Axis Internet Dynamic DNS ServiceLinux/Unix example Axis Video Hosting System AvhsDNS Configuration Advanced TCP/IP SettingsNTP Configuration Host Name ConfigurationNAT traversal port mapping for IPv4 HttpsSocks QoS Quality of ServiceUPnPTM StorageRTP/H.264 BonjourMount and Unmount SD Card Network ShareFormat SD Card To add a network sharePorts & Devices MaintenancePorts Port StatusSupport Overview SupportSystem Overview Logs & ReportsFile Upload Reset to Factory Default SettingsPlain Config Upgrade the Firmware TroubleshootingFirmware To upgrade the product’s firmware Check the FirmwareSymptoms, Possible Causes and Remedial Actions Emergency Recovery ProcedureProblems setting the IP address Product cannot be accessed from a browserBasic Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, general Status and Network indicator LEDs are flashing red rapidlySetup Video & Audio Camera Settings SettingsVideo cannot be recorded Technical Specifications Installation Function/group Specifications Network SecurityMaintenance SupportedPower Function/group Specifications General CasingConnectors DimensionsFunction Pin Specifications ConnectorsAudio Output Performance ConsiderationsAudio Input M3.11
Top Page Image Contents