Axis Communications AXIS P1343 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD card

Page 44

AXIS P1343 Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 38. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 47.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD card

The SD/SDHC memory card (not included) is managed on the System Options > Storage page. Click SD card to open Storage Management.

Mounting is done automatically when the card is inserted or when the product boots. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Format an SD card so that it can be written to one of two available options — VFAT and ext4. During the formatting any previous data stored on the disk will be lost. The recommended format is ext4, due to its resilience against data loss if the card is ejected or if there is abrupt power loss. A third-party ext4 driver or application is also needed to access the file system from Windows.

Note that most SD cards are pre-formatted with vFAT when purchased. The Check Disk option is used to check for errors on the SD card and only works for the file system ext4. The Repair option repairs the SD card of errors in the file system ext4. For vFAT file system use a card reader or PC to perform card maintenance.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Axis P1343 Network Camera About this document LiabilityIntellectual Property Rights Equipment ModificationsTable of Contents Axis P1343 Network CameraSymptoms, possible causes and remedial actions Performance considerationsHardware overview Hardware overviewConnectors For technical specifications, seeColor Indication LED indicatorsFunction Pin Specifications Replacing the lens Status LED when using Focus AssistantMaintenance Accessing the product Accessing the productAccess from a browser Start a browser Internet Explorer, Firefox, SafariAccess from the Internet Set the root passwordNetwork TCP/IP Advanced Click Create self-signed certificateLive View Controls on the Live ViewAMC Audio controls Axis Media Control viewer toolbarPTZ Controls Axis P1343 Network Camera How to stream H.264 Media streamsMedia streams Axis Media Control AMCAlternative methods of accessing the video stream QuickTimeTM. The following paths can be usedAccessing audio streams Java applet supports simplex audio with G.711 encodingBasic Setup Setting up the productSetting up the product Video and Audio Video and AudioVideo Stream Pixel Counter264 Stream ProfilesImage Camera Settings Exposure SettingsImage Appearance White balanceView Area OverlayAudio Settings Privacy MaskFocus Audio ChannelsAudio Input G711 G726Audio Clips Audio OutputLive View Config Default viewer for browsersLive View Config Viewer Settings User Defined LinksOutput Buttons Browser Viewer DescriptionPreset Positions PTZ Pan Tilt ZoomPTZ Pan Tilt Zoom Guard TourAdvanced ControlsDetectors DetectorsCamera Tampering Motion DetectionSet up motion detection Motion detection parametersDefault values Audio detectionRecommended values 15% 60-90% 75-95%Applications ApplicationsSetting Up an Action Rule EventsEvents Convert Event Types to Action RulesRecurrences RecipientsSchedules Axis P1343 Network Camera Recordings RecordingsRecording List Continuous recordingAxis P1343 Network Camera System Options System OptionsSecurity UsersAudio Support Date & TimeIeee Basic TCP/IP Settings NetworkIPv4 Address Configuration IPv6 Address Configuration Advanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailStorage UPnPTMRTP/H.264 BonjourMaintenance Ports & DevicesNetwork Share PortsSupport Support OverviewSystem Overview Logs & ReportsReset to factory default settings ScriptingFile Upload Plain ConfigAxis P1343 Network Camera Troubleshooting TroubleshootingEmergency recovery procedure Checking the firmwareProduct cannot be accessed from a browser Symptoms, possible causes and remedial actionsProblems setting the IP address Status and Network indicator LEDs are flashing red rapidly Product is accessible locally but not externallyProblems with the H.264 format Video and image problems, general Setup Video & Audio Camera SettingsProblems uploading files No images displayed on webSettings Storage and disk management problemsNo audio Poor audio qualityTechnical Specifications Technical SpecificationsMaintenance Installation aids Function/group Specifications Built-inMicrophone Specification Network SecurityPerformance considerations Axis P1343 Network Camera M1.6
Top Page Image Contents