Axis Communications AXIS P1343 user manual Connectors, For technical speciﬁcations, see

Page 6

AXIS P1343 Network Camera

Hardware overview

Connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet (PoE).

Caution

To protect the product against power surges, a shielded network cable (STP) must be used between the product and the network switch. Ensure that the network switch is properly grounded.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in ampliﬁer. A stereo connector must be used for the audio out.

SD card slot - A standard or high-capacity SD card (not included) can be used for local recording with removable storage. For instructions on how to insert and remove an SD card, please refer to the Installation Guide.

Note

Before removal, the SD card should be unmounted to prevent corruption of recordings. To unmount the SD card, go to Setup > System Options > Storage > SD Card and click Unmount.

Control button - The control button is used for:

•Enabling the Focus Assistant. Press and very quickly release the Control button.

•Connecting to an AXIS Video Hosting System service. See page 41. To connect, press and hold the button for about 1 second until the Status LED ﬂashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 41. To connect, press and hold the button for about 3 seconds.

•Resetting the product to factory default settings. See page 47.

Power connector - 2-pin terminal block for power input.

I/O connector

DC power input

Note

For technical speciﬁcations, see page 54.

I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notiﬁcations. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

•Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

6

Image 6

Contents Axis P1343 Network Camera Intellectual Property Rights About this documentLiability Equipment Modiﬁcations Table of Contents Axis P1343 Network CameraSymptoms, possible causes and remedial actions Performance considerationsHardware overview Hardware overviewConnectors For technical speciﬁcations, seeLED indicators Function Pin SpeciﬁcationsColor Indication Status LED when using Focus Assistant MaintenanceReplacing the lens Access from a browser Accessing the productAccessing the product Start a browser Internet Explorer, Firefox, SafariNetwork TCP/IP Advanced Access from the InternetSet the root password Click Create self-signed certiﬁcateLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ ControlsAMC Audio controls Axis P1343 Network Camera Media streams How to stream H.264Media streams Axis Media Control AMCAlternative methods of accessing the video stream QuickTimeTM. The following paths can be usedAccessing audio streams Java applet supports simplex audio with G.711 encodingSetting up the product Setting up the productBasic Setup Video Stream Video and AudioVideo and Audio Pixel CounterStream Proﬁles Image264 Image Appearance Camera SettingsExposure Settings White balanceView Area OverlayFocus Audio SettingsPrivacy Mask Audio ChannelsAudio Input G711 G726Audio Clips Audio OutputDefault viewer for browsers Live View ConﬁgLive View Conﬁg Output Buttons Viewer SettingsUser Deﬁned Links Browser Viewer DescriptionPTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom Guard TourAdvanced ControlsCamera Tampering DetectorsDetectors Motion DetectionSet up motion detection Motion detection parametersRecommended values Default valuesAudio detection 15% 60-90% 75-95%Applications ApplicationsEvents Setting Up an Action RuleEvents Convert Event Types to Action RulesRecipients SchedulesRecurrences Axis P1343 Network Camera Recording List RecordingsRecordings Continuous recordingAxis P1343 Network Camera Security System OptionsSystem Options UsersDate & Time IeeeAudio Support IPv4 Address Conﬁguration Basic TCP/IP SettingsNetwork IPv6 Address ConﬁgurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 StorageUPnPTM BonjourNetwork Share MaintenancePorts & Devices PortsSystem Overview SupportSupport Overview Logs & ReportsFile Upload Reset to factory default settingsScripting Plain ConﬁgAxis P1343 Network Camera Emergency recovery procedure TroubleshootingTroubleshooting Checking the ﬁrmwareSymptoms, possible causes and remedial actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with the H.264 formatStatus and Network indicator LEDs are ﬂashing red rapidly Problems uploading ﬁles Video and image problems, generalSetup Video & Audio Camera Settings No images displayed on webNo audio SettingsStorage and disk management problems Poor audio qualityTechnical Speciﬁcations Technical SpeciﬁcationsMicrophone Maintenance Installation aidsFunction/group Speciﬁcations Built-in Speciﬁcation Network SecurityPerformance considerations Axis P1343 Network Camera M1.6