Panasonic WV-CL924A operating instructions Special Menu Special

Page 36

10. Special Menu (SPECIAL)

This menu lets you adjust and set up the video signal of the camera to meet your requirements.

Move the cursor to END on the bottom line of the CAM

SET UP menu and press and simultaneously

(hold down and press ) for 2 seconds or more. The SPECIAL menu appears on the monitor as shown below.

 

** CAM SET UP **

** SPECIAL **

 

CAMERA ID

OFF

UP SIDE DOWN

OFF

 

ALC/ELC

 

ALC

 

SHUTTER

 

OFF

 

CHROMA GAIN

....I....

AGC

 

ON (DNR-H)

AP GAIN

....I....

SENS UP

 

OFF

 

PEDESTAL

.I

SYNC

 

INT

 

HUE

.I

WHITE BAL

ATW1

 

-

+

MOTION DET

OFF

 

BW

OFF

 

LENS DRIVE

DC

 

BURST (BW)

ON

 

 

 

 

 

 

 

CAMERA RESET

PUSH SW

 

 

END

 

SET UP ENABLE

RET END

 

 

10-2. Chroma Level Setting (CHROMA GAIN)

1.Move the cursor to the CHROMA GAIN parameter.

2.While observing the vectorscope or color video monitor, move the “I” cursor to adjust the chroma level.

10-3. Aperture Gain Setting (AP GAIN)

1.Move the cursor to the AP GAIN parameter.

2.While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the aperture gain level.

10-4. Pedestal Level Setting (PEDESTAL)

1.Move the cursor to the PEDESTAL parameter.

2.While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the pedestal level (black level).

10-1. Camera Picture Upside Down Positioning

(UP SIDE DOWN)

1.Move the cursor to the UP SIDE DOWN parameter.

2.Select ON when you want to turn the picture upside down.

10-5. Chroma Phase (Hue) Setting (HUE)

1.Move the cursor to the HUE parameter.

2.While observing the vectorscope or color video monitor, move the “I” cursor to adjust the hue (chroma phase) level.

10-6 BW

1.Move the cursor to the BW parameter.

2.Select AUTO1, AUTO2, ON or OFF using or

.

-37-

Image 36
Contents Operating Instructions Bol, within an equilateral triangle, is Contents Features PrefacePrecautions Clean the CCD faceplate with careDo not attempt to disassemble the camera Handle the camera with careMajor Operating Controls and Their Functions WV-CL924Auto Iris Lens Connector Flange-back Adjusting Ring FB0Gen-lock Termination Switch Hi-Z, G/L 75Ω 1Gen-lock Input Connector GEN-LOCK3Power Cord Socket 4AC/DC Compatible Input Terminal DC 12V IN/AC 24VConnections WV-CL920 120 V AC 60HzWV-CL924 12 V DC/24 V AC AC Power Supply Recommended wire gauge sizes for 24 V AC lineInstallation of Auto Iris Lens Connector Mounting the Lens Focus or FLANGE-BACK Adjustment Installation of Camera Mounting from the topSetup Camera Setup MenuATW1 ATW2 AWC Opening the Setup Menu Press and hold down for 2 seconds or moreSetup Operation All Reset OperationEditing the CAM SET UP Menu Important NoticeSetting Procedures Camera Identification Camera ID SettingTo edit the Camera ID To enter a blank space in the Camera IDLight Control Setting ALC/ELC To erase all characters in the editing areaTo determine the display position of the Camera ID ALC Mode with Preset on Back Light Compensation Back Light CompALC Mode with Preset OFF Blinking Shutter Speed Setting Shutter Gain Control Setting AGC ON/OFFElectronic Sensitivity Enhancement Sens UP Synchronization Setting Sync Important NoticesVBS Gen-lock Mode Extvbs Page VS Gen-lock Mode Extvs Line-lock Sync Mode LLPhase Coarse White Balance Setting White BAL Auto-Tracing White Balance Mode ATWATW1 Auto Tracing White Balance Manual Fine Adjustment for AWC ATW Select AWC →Motion Detector Setting Motion DET Lens Drive Signal Selection Lens DriveSpecial Menu Special Burst BW To reset to the factory settings Prevention of Blooming and SmearSpecifications AGCPage Standard Accessories Optional Accessories Panasonic Canada Inc