Cisco Systems CIVS-IPC-2621V manual Adjusting the Camera Lens on the 2621 IP Dome

Page 39

Chapter 2 Getting Started

Adjusting the Video Image

camera at an object that is at least 15 feet (4.5 meters) away and gently sliding the lens toward or away from the camera. Take care not to pull the lens completely away from the camera.Obtain a sharp picture in both wide-angle and telephoto positions. When the focus is set as desired, use the Allen wrench to tighten the back focus hex screw.

Caution Do not manually adjust the focus or zoom for the IP camera. Attempting to manually do so may damage the IP camera lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

Figure 2-16 Adjusting the Camera Lens on the 2621 IP Dome

1

2

1Rotation wheel

2Panning lock screw

3Tilt lock screws (2)

4Back focus hex screws (3)

3

4

Step 4 Remove the analog monitor cable from the analog video output port.

Step 5 Replace the privacy shield by squeezing it to fit inside the four tabs on the camera unit.

Make sure to adjust the privacy shield inside the dome and trim ring assembly so that it does not block the lens from capturing video.

Step 6 Align the tab on the dome assembly with the opening in the base plate, press the dome assembly into place, and securing the three TORX screws

		Cisco Video Surveillance System 2621 IP Dome User Guide
		Cisco Video Surveillance System 2621 IP Dome User Guide
	OL-24129-02			2-27
	OL-24129-02			2-27

Image 39

Contents Americas Headquarters Cisco Video Surveillance 2621 IP Dome User GuideCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Organization OverviewViii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2621 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2621 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedInstalling the Cisco Video Surveillance 2621 IP Dome Preparing for Installation, Mounting with a Junction Box,Preventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Preparing for InstallationMounting with a Junction Box ProcedureDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a Conduit BaseBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on 13 Securing Torx Screws Mounting on a Solid Surface14 Disassembling the 2621 IP Dome Components See -1 on 15 Securing Torx Screws Performing the Initial Setup of the IP CameraProtocol//ipaddress Http//203.70.212.52 Accessing the IP Camera WindowsHttps//192.168.0.100 Https//203.70.212.521024Http//203.70.212.521024 Adjusting the Video Image16 Adjusting the Camera Lens on the 2621 IP Dome Initial Setup of the IP Camera Powering the IP Camera On or OffResetting the IP Camera Reset Type Procedure RemarksCleaning the IP Camera OL-24129-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Audio Window Controls section onDuplex Talk and Listen Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orSecurity Windows Initialization WindowInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsStatus Windows System WindowSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogLog List Message ExplanationSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24129-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsAccessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8

Related manuals

Manual 108 pages 61.32 Kb