Cisco Systems CIVS-IPC-2621V manual Option Description

Page 51

Chapter 3 Configuring and Managing the IP Camera

Setup Windows

Table 3-3

Advanced Setup Window Options (continued)

 

 

 

Option

 

Description

 

 

Max RTP Video Packet

Maximum number of bytes per video packet that are sent in each RTP

Length

 

request.

 

 

Configure a lower number if you are streaming video to a cell phone that

 

 

requires smaller data packets.

 

 

Valid values are 400 through 1400. The default value is 1400.

 

 

Max RTP Audio Packet

Maximum number of bytes per audio packet that are sent in each RTP

 

 

request.

 

 

Configure a lower number if you are streaming video to a cell phone that

 

 

requires smaller data packets.

 

 

Valid values are 400 through 1400. The default value is 1400.

 

 

Enable Multicast

Check this check box to send video and audio data as a multicast stream.

 

 

When multicast is enabled, the IP camera sends video and audio to the

 

 

multicast addresses that you designate. Multicast enables multiple devices to

 

 

receive the video signal from the IP camera simultaneously.

 

 

 

Video Address

 

Appears if you enabled multicast. Enter the multicast IP address on which

 

 

the IP camera sends a video stream.

 

 

The default value is 224.2.0.1.

 

 

 

Video Port

 

Appears if you enabled multicast. Enter the port on which the IP camera

 

 

sends a multicast video stream.

 

 

Valid values are even numbers 1024 through 65534. The default value is

 

 

2240.

 

 

 

Audio Address

 

Appears if you enabled multicast. Enter the multicast IP address on which

 

 

the IP camera sends an audio stream.

 

 

The default value is 224.2.0.1.

 

 

 

Audio Port

 

Appears if you enabled multicast. Enter the port on which the IP camera

 

 

sends a multicast audio stream.

 

 

Valid values are even numbers 1024 through 65534. The default value is

 

 

2242.

 

 

 

Time to Live

 

Appears if you enabled multicast. Enter the number of hops, which specifies

 

 

the number of network devices that an audio-video stream can pass before

 

 

arriving at its destination or being dropped.

 

 

Valid values are 1 through 255. The default value is 16.

 

 

 

Cisco Video Surveillance System 2621 IP Dome User Guide

 

OL-24129-02

3-9

 

 

 

Image 51
Contents Americas Headquarters Cisco Video Surveillance 2621 IP Dome User GuideCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Organization OverviewViii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2621 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2621 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedInstalling the Cisco Video Surveillance 2621 IP Dome Preparing for Installation, Mounting with a Junction Box,Preventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Preparing for InstallationMounting with a Junction Box ProcedureDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a Conduit BaseBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on 13 Securing Torx Screws Mounting on a Solid Surface14 Disassembling the 2621 IP Dome Components See -1 on 15 Securing Torx Screws Performing the Initial Setup of the IP CameraProtocol//ipaddress Http//203.70.212.52 Accessing the IP Camera WindowsHttps//192.168.0.100 Https//203.70.212.521024Http//203.70.212.521024 Adjusting the Video Image16 Adjusting the Camera Lens on the 2621 IP Dome Initial Setup of the IP Camera Powering the IP Camera On or OffResetting the IP Camera Reset Type Procedure RemarksCleaning the IP Camera OL-24129-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Audio Window Controls section onDuplex Talk and Listen Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orSecurity Windows Initialization WindowInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsStatus Windows System WindowSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogLog List Message ExplanationSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24129-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsAccessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 108 pages 61.32 Kb