Cisco Systems CIVS-IPC-2621V manual Privacy Region Window, Focus/Zoom Window

Page 66

Chapter 3 Configuring and Managing the IP Camera

Audio/Video Windows

Table 3-10

Audio Window Options (continued)

 

 

 

Option

 

Description

 

 

Enable External

Display only. A check indicates that a speaker that is connected to the IP

Speaker

 

camera is enabled.

 

 

The speaker is enabled when you check the Enable Audio check box and

 

 

choose Simplex - Talk Only, Half Duplex - Talk or Listen, or

 

 

Full Duplex - Talk and Listen to make this check box available.

 

 

 

Audio Type

 

Choose the codec for audio that is transmitted from the IP camera.

 

 

This option is available when you check the Enable Audio check box and

 

 

choose Simplex - Listen Only, Half Duplex - Talk or Listen, or

 

 

Full Duplex - Talk and Listen.

 

 

 

Privacy Region Window

The Privacy Region window provides options for creating up to four user-defined masking zones that can be used to provide regions of privacy in the camera field of view. Video within privacy regions is not recorded in the camera, nor sent in the video stream. Instead of the actual video, privacy regions display one of the colors available from the Region Color drop-down list.

To display the Privacy Region window, access the configuration windows as described in the “Accessing the IP Camera Windows” section on page 2-6, click Audio/Video, then click Privacy Region.

If you change any options in the Privacy Region window, you must click Apply to save the changes.

Table 3-11describes the options in the Privacy Region window.

Table 3-11

Privacy Region Window Options

 

 

 

Option

 

Description

 

 

 

Region 1

 

Check up to four of the Region check boxes to enable privacy regions. A

Region II

 

window appears in the field of view for each enabled privacy region. To

Region III

 

configure a window, drag it to the desired area, then drag an edge or corner

Region IV

 

to resize it. If desired, enter a name of up to 12 characters for each region in

 

 

the text box next to the corresponding check box.

 

 

To disable a privacy region and remove its window from the field of view,

 

 

uncheck the associated check box.

 

 

 

Region Color

 

Choose a color from the Region Color drop-down list to specify the color

 

 

that will be used to mask the actual video in all enabled privacy regions.

 

 

 

Focus/Zoom Window

The Focus/Zoom window provides controls for remotely setting the focus and zoom level for the IP camera. In addition to the focus and zoom controls, the Focus/Zoom window displays real-time video from the camera, which allows you to achieve the sharpest image for your preferred field of view.

To display the Focus/Zoom window, access the configuration windows as described in the “Accessing the IP Camera Windows” section on page 2-25, click Audio/Video, then click Focus/Zoom.

Table 3-12describes the options in the Focus/Zoom window.

 

Cisco Video Surveillance System 2621 IP Dome User Guide

3-24

OL-24129-02

Image 66
Contents Cisco Video Surveillance 2621 IP Dome User Guide Americas HeadquartersCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Overview OrganizationViii Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2621 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2621 IP DomePackage Contents Getting Started Before You BeginInstalling the Cisco Video Surveillance 2621 IP Dome Preparing for Installation, Mounting with a Junction Box,Preventing Electrostatic Discharge Damage Preparing for Installation Passing the Audio Cable through a Ferrite CoreProcedure Mounting with a Junction BoxDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Mounting with a Conduit Base Attaching the Privacy Shield and DomeBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on Mounting on a Solid Surface 13 Securing Torx Screws14 Disassembling the 2621 IP Dome Components See -1 on Performing the Initial Setup of the IP Camera 15 Securing Torx ScrewsProtocol//ipaddress Https//203.70.212.521024 Accessing the IP Camera WindowsHttps//192.168.0.100 Http//203.70.212.52Adjusting the Video Image Http//203.70.212.52102416 Adjusting the Camera Lens on the 2621 IP Dome Reset Type Procedure Remarks Powering the IP Camera On or OffResetting the IP Camera Initial Setup of the IP CameraCleaning the IP Camera OL-24129-02 Configuring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Privacy Region See the Alarm I/O PortsSee the Audio Window section See the Focus/Zoom WindowNavigating the Configuration Windows SnmpDevice Settings Setup WindowsBasic Setup Window Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Audio Window Controls section onDuplex Talk and Listen Choose Simplex Talk Only , Half Duplex Talk or Listen , or Privacy Region WindowFocus/Zoom Window Full Duplex Talk and ListenSecurity Windows Initialization WindowInitialization Window, Complexity Window, Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowPrimary Smtp Server Described in the Basic Setup Window section onMail Setup Secondary Smtp ServerSecondary FTP Mail BodyPrimary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Clear button Event ScheduleNew Schedule Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm Output Settings Alarm I/O Ports WindowAlarm Input Settings Manual Control SettingsStatus Windows System WindowSystem Status Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerLog List Message ExplanationSystem log messages Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24129-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Digital zoom controls Home Window ControlsControl Description Audio controlsIP camera controls Snapshot controlsSave For related information, see the Video Window section onAccessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing the Mjpeg Stream Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 108 pages 61.32 Kb