Cisco Systems CIVS-IPC-2621V manual Adjusting the Video Image, Http//203.70.212.521024

Page 38

Chapter 2 Getting Started

Adjusting the Video Image

Enter the following for a non-secure connection if the IP address is 203.70.212.52 and the HTTP port number is 1024:

http://203.70.212.52:1024

Step 2 Enter your IP camera user name and password when prompted, then click OK.

To log in as the IP camera administrator, enter the user name admin (all lower case) and the password that is configured for the administrator. To log in as a user, enter the user name and password that are configured for the user.

The Main window appears and video from the IP camera starts playing automatically. You can take these actions in the Main window:

Click the Setup link to access configuration menus for the camera. For detailed information about these menus, see Chapter 3, “Configuring and Managing the IP Camera.”

Click the Home link to view and control live video from the camera. For detailed information about these actions, see Chapter 4, “Viewing Live Video.”

Click the Logout button to exit the window.

Adjusting the Video Image

As part of the IP camera installation process, you make pan and tilt settings (and back focus settings if necessary) for the camera in the dome. If you ever need to change these settings, follow these steps:

Procedure

Step 1 Unscrew the three security TORX screws using the TORX screwdriver that supplied with the IP dome and pull the dome assembly away from the base plate

Step 2 Remove the Privacy shield by squeezing it inward to release it from the four tabs that hold it into place (see Figure 2-2).

Step 3 See Figure 2-16and take these actions to adjust the camera lens to obtain the desired image

Temporarily attach an analog monitor to the IP dome so that you can see video while adjusting the camera. If the cable from the monitor terminates with a 3.5 mm jack, plug it into the analog video output port on the IP dome. If the cable terminates with a BNC connector, connect it to the mini cable with BNC adapter, then plug the cable into the analog video output port. The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can purchase from Cisco (Cisco part number CIVS-IPCA-1017=).

Make the following adjustments, viewing the video on the analog monitor as needed:

Rotation—The rotation is factory set and should not require adjustments. In the event that it does need to be adjusted, turn the notched rotation wheel until you achieve the desired image.

Pan—Use a Phillips-head to loosen the panning lock screw (the one slightly recessed in a cutout), then rotate the camera to obtain the desired image, then tighten the panning lock screw.

Tilt—Loosen the two tilt lock screws, adjust the lens to obtain the desired image, then tighten the screws.

Back focus—The back focus is factory set for optimal use and should not require adjustments. In the event that it does need to be adjusted, use the 0.9 mm Allen wrench that is supplied with the IP camera to loosen the back focus hex screw, then adjust the back focus by aiming the IP

 

Cisco Video Surveillance System 2621 IP Dome User Guide

2-26

OL-24129-02

Image 38
Contents Cisco Video Surveillance 2621 IP Dome User Guide Americas HeadquartersCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Overview OrganizationViii Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2621 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2621 IP DomePackage Contents Getting Started Before You BeginPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2621 IP DomePreparing for Installation, Mounting with a Junction Box, Preparing for Installation Passing the Audio Cable through a Ferrite CoreProcedure Mounting with a Junction BoxDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Mounting with a Conduit Base Attaching the Privacy Shield and DomeBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on Mounting on a Solid Surface 13 Securing Torx Screws14 Disassembling the 2621 IP Dome Components See -1 on Performing the Initial Setup of the IP Camera 15 Securing Torx ScrewsProtocol//ipaddress Https//203.70.212.521024 Accessing the IP Camera WindowsHttps//192.168.0.100 Http//203.70.212.52Adjusting the Video Image Http//203.70.212.52102416 Adjusting the Camera Lens on the 2621 IP Dome Reset Type Procedure Remarks Powering the IP Camera On or OffResetting the IP Camera Initial Setup of the IP CameraCleaning the IP Camera OL-24129-02 Configuring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Privacy Region See the Alarm I/O PortsSee the Audio Window section See the Focus/Zoom WindowNavigating the Configuration Windows SnmpDevice Settings Setup WindowsBasic Setup Window Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEAP-FAST Options Eapol WindowEAP-TLS Options Users Window Administration WindowsUsers Window, Maintenance Window, Firmware Window, Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Duplex Talk and Listen Audio WindowControls section on Choose Simplex Talk Only , Half Duplex Talk or Listen , or Privacy Region WindowFocus/Zoom Window Full Duplex Talk and ListenInitialization Window, Complexity Window, Security WindowsInitialization Window Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowPrimary Smtp Server Described in the Basic Setup Window section onMail Setup Secondary Smtp ServerSecondary FTP Mail BodyPrimary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Clear button Event ScheduleNew Schedule Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm Output Settings Alarm I/O Ports WindowAlarm Input Settings Manual Control SettingsSystem Status Status WindowsSystem Window Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerSystem log messages Log ListMessage Explanation Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24129-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Digital zoom controls Home Window ControlsControl Description Audio controlsIP camera controls Snapshot controlsSave For related information, see the Video Window section onViewing Video through Third-Party Devices or Software Accessing the Primary H.264 StreamAccessing Secondary H.264 Stream Accessing the Mjpeg Stream Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 108 pages 3.3 Kb