Cisco Systems CIVS-IPC-2621V manual Attaching the Camera Unit to the Base Plate

Page 19

Chapter 2 Getting Started

Installing the Cisco Video Surveillance 2621 IP Dome

Step 8 (Optional) Use the GPIO ports to connect external devices that trigger alarms (connect through alarm input ports) or respond to alarms (connect through alarm output ports). (See Figure 1-1 on page 1-3.)

Step 9 Attach the camera unit to the base plate by aligning the three tabs on the camera unit with the slots on the base plate, pressing the camera unit into the base plate until the tabs snap into place, and securing the camera unit with the two camera unit screws (see Figure 2-4).

Figure 2-4 Attaching the Camera Unit to the Base Plate

1

2

Base plate

Camera unit

Step 10 See Figure 2-16 on page 2-27and take these actions to adjust the camera lens to obtain the desired image

•Temporarily attach an analog monitor to the IP dome so that you can see video while adjusting the camera. If the cable from the monitor terminates with a 3.5 mm jack, plug it into the analog video output port on the IP dome. If the cable terminates with a BNC connector, connect it to the optional mini cable with BNC adapter, then plug the cable into the analog video output port. The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can purchase from Cisco (Cisco part number CIVS-IPCA-1017=).

•Make the following adjustments, viewing the video on the analog monitor as needed:

Cisco Video Surveillance System 2621 IP Dome User Guide

	OL-24129-02	2-7

Image 19

Contents Americas Headquarters Cisco Video Surveillance 2621 IP Dome User GuideCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Organization OverviewViii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2621 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2621 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreparing for Installation, Mounting with a Junction Box, Installing the Cisco Video Surveillance 2621 IP DomePreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Preparing for InstallationMounting with a Junction Box ProcedureDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a Conduit BaseBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on 13 Securing Torx Screws Mounting on a Solid Surface14 Disassembling the 2621 IP Dome Components See -1 on 15 Securing Torx Screws Performing the Initial Setup of the IP CameraProtocol//ipaddress Http//203.70.212.52 Accessing the IP Camera WindowsHttps//192.168.0.100 Https//203.70.212.521024Http//203.70.212.521024 Adjusting the Video Image16 Adjusting the Camera Lens on the 2621 IP Dome Initial Setup of the IP Camera Powering the IP Camera On or OffResetting the IP Camera Reset Type Procedure RemarksCleaning the IP Camera OL-24129-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Controls section on Audio WindowDuplex Talk and Listen Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orInitialization Window Security WindowsInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsSystem Window Status WindowsSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogMessage Explanation Log ListSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24129-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8

Related manuals

Manual 108 pages 3.3 Kb