Cisco Systems CIVS-IPC-2621V manual IP Filter Window, QoS

Page 52

Chapter 3 Configuring and Managing the IP Camera

Setup Windows

Table 3-3

Advanced Setup Window Options (continued)

 

 

 

Option

 

Description

 

 

 

QoS

 

 

 

 

Enable QoS Mode

Check this check box and click the Audio, Video, or Both radio button to

 

 

enable Quality of Service (QoS) for audio streams, video streams, or both

 

 

streams.

 

 

Note QOS applies to Layer 3 only, and is applied to ASF and RTP video

 

 

streams. When QOS is applied to an ASF video stream, DSCP values

 

 

are not distinguished between audio and video streams because they

 

 

are applied to the same stream. When QOS is applied to an RTP

 

 

video stream, DSCP values are distinguished between audio and

 

 

video streams because they are applied to different streams.

 

 

 

DSCP

 

If you enable QoS, enter the Differentiated Services Code Point (DSCP) to

 

 

be used to process QoS packets.

 

 

The default value is 12.

 

 

 

IP Filter Window

The IP Filter window provides options for controlling access to the IP camera by designating a list of IP addresses that can access the IP camera and a list of IP addresses that cannot access the IP camera.

To display the IP Filter window, access the configuration windows as described in the “Accessing the IP Camera Windows” section on page 2-25, click Setup, then click IP Filter.

If you change any options in the IP Filter window, you must click Save to save the changes. To discard the changes, click Cancel before clicking Save. These buttons appear at the bottom of the window. You may need to scroll down to see them.

Table 3-4describes the options in the IP Filter window.

Table 3-4 IP Filter Window Options

Option

Options

Description

Choose the option that specifies how to control IP addresses from which the IP camera can be accessed:

Disable—Do not use the IP address filtering feature. In this case, the IP camera can be accessed from a device with any IP address.

Enable and deny the following IP address—Lets you designate one or more IP addresses or range of IP addresses that cannot access the IP camera. All other IP addresses can access the IP camera.

Enable and allow the following IP address—Lets you designate one or more IP addresses or range of IP addresses that can access the IP camera. All other IP addresses cannot access the IP camera.

 

Cisco Video Surveillance System 2621 IP Dome User Guide

3-10

OL-24129-02

Image 52
Contents Cisco Video Surveillance 2621 IP Dome User Guide Americas HeadquartersCisco Video Surveillance System 2621 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM Overview OrganizationViii Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2621 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2621 IP DomePackage Contents Getting Started Before You BeginPreparing for Installation, Mounting with a Junction Box, Installing the Cisco Video Surveillance 2621 IP DomePreventing Electrostatic Discharge Damage Preparing for Installation Passing the Audio Cable through a Ferrite CoreProcedure Mounting with a Junction BoxDisassembling the 2621 IP Dome Components Attaching the Base Plate to a Junction Box Attaching the Camera Unit to the Base Plate Cisco Video Surveillance System 2621 IP Dome User Guide Mounting with a Conduit Base Attaching the Privacy Shield and DomeBase plate Camera unit Camera unit screws Attaching the Conduit Base to a Surface Attaching the Base Plate to the Conduit Base See -1 on Cisco Video Surveillance System 2621 IP Dome User Guide 10 Attaching the Privacy Shield and Dome Mounting to a Ceiling Tile 11 Disassembling the 2621 IP Dome Components 12 Preparing the 2621 IP Dome Ceiling Tile See -1 on Mounting on a Solid Surface 13 Securing Torx Screws14 Disassembling the 2621 IP Dome Components See -1 on Performing the Initial Setup of the IP Camera 15 Securing Torx ScrewsProtocol//ipaddress Accessing the IP Camera Windows Https//192.168.0.100Https//203.70.212.521024 Http//203.70.212.52Adjusting the Video Image Http//203.70.212.52102416 Adjusting the Camera Lens on the 2621 IP Dome Powering the IP Camera On or Off Resetting the IP CameraReset Type Procedure Remarks Initial Setup of the IP CameraCleaning the IP Camera OL-24129-02 Configuring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Alarm I/O Ports See the Audio Window sectionSee the Privacy Region See the Focus/Zoom WindowNavigating the Configuration Windows SnmpSetup Windows Basic Setup WindowDevice Settings Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Controls section on Audio WindowDuplex Talk and Listen Privacy Region Window Focus/Zoom WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window Security WindowsInitialization Window, Complexity Window, Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowDescribed in the Basic Setup Window section on Mail SetupPrimary Smtp Server Secondary Smtp ServerMail Body Primary FTPSecondary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Event Schedule New ScheduleClear button Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm I/O Ports Window Alarm Input SettingsAlarm Output Settings Manual Control SettingsSystem Window Status WindowsSystem Status Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerMessage Explanation Log ListSystem log messages Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24129-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Home Window Controls Control DescriptionDigital zoom controls Audio controlsSnapshot controls SaveIP camera controls For related information, see the Video Window section onAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing the Primary MPEG-4 Stream Accessing Dual MPEG-4 StreamsAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24129-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24129-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 108 pages 3.3 Kb