AT&T 8110, 8102 Flash button, Program button, Tone Selector Fast or Slow Ringer Volume control

Page 13

Mute button

(On the 8110 only)

Message light

Dial pad

Handset jack

Speaker button (On the 8110 only)

Flash button

For turning off the microphone associated with the handset or the built-in speakerphone.

A red light that flashes when a message has been left for you.

The standard 12-button pad for dialing telephone numbers. The dial pad is also used with the PROGRAM button to store numbers on the Programmable Dialing buttons.

For connecting the handset to your telephone.

For accessing the built-in speakerphone and microphone combination.

For using features such as Conference with business communications systems, and for custom calling features if you are using your telephone at home.

Program button

For storing telephone numbers on the

 

programmable dialing buttons on the front of

 

your telephone.

The SIDE VIEW shows the following features:

Tone Selector (HI or LO)

Tone Selector (FAST or SLOW)

Ringer Volume control

For selecting one of 2 tone ringer frequencies (high or low).

For selecting one of 2 tone ringer modulation rates (fast or slow).

A3-position switch to control the volume for the tone ringer. Slide it up (away from you) for a louder ring, down (toward you) for a quieter ring. The volume control is

labeled

Ringer Vol

.

Speaker volume control For raising or lowering the volume of the

(On the 8110 only) built-in speakerphone. The volume control

is labeled Speakerphone Vol .

10

Image 13
Contents AT&T Trademarks Contents Use Important Safety InstructionsService Emploi Consignes DE Securite ImportantesEntretien Conservez CES InstructionsAppendix B Your 8102 and 8110 TelephonesPage TOP View 8110 Telephone Top, Side, and Bottom Views Auto Answer button On the 8110 only Handset Adjunct equipment jack On the 8102 onlyFlash button Tone Selector Fast or Slow Ringer Volume controlProgram button Line jack Table/Desk Installation Installing Your TelephoneHandset cord jack Handset jack Rotating the Handset Tab Wall InstallationTriangle Mounting studs Base Base Locking Tab Voice Terminal Wall Labeling the Programmable Dialing Button Designation Card Using the FeaturesRemoving and Covering the Auto Answer Button Page Answering and Placing a Call Using the FeaturesTo end a call To place a call using the speakerphone for 8110 usersAuto Answer for 8110 Users To turn off the Auto Answer featureTo have your telephone automatically answer a call Hold FlashTo put a call on hold To return to the held callMute for 8110 Users MessageProgrammable Dialing Buttons Personalized RingProgrammable Dialing Buttons To dial a number with a programmable dialing button Redial With Auto-PauseTo erase a number stored on a programmable dialing button To program an automatic pause for redialed numbers To erase ALL stored access codesTo place/answer a call without lifting the handset Speakerphone for 8110 UsersTo prevent other party from hearing you To mute microphone To change from speakerphone to handsetAppendix a Page Answering Calls Appendix BOriginating Calls Putting Calls on HoldSwitching from the Headset to the Handset Appendix C Auxiliary Power for the 8110 TelephoneIf Your Telephone Does Not Respond Appendix DConnection and USE with the Nationwide Telephone Network FCC Registration and Repair InformationRight of the Telephone Company Interference InformationAT&T Warranty Information Dialing Numbers in Memory Storing Numbers in MemoryErasing a Number in Memory Holding and Returning to a CallUsing the Auto Answer Feature For 8110 Users Only Using the Built-in Speakerphone For 8110 Users OnlyComcode 555-015-131 Graphics AT&T Issue 2, March
Related manuals
Manual 4 pages 29.68 Kb