Approach Tech LC-7314 manual Product Instructions, Product Features, Camera, Video Signal

Page 6

1.PRODUCT FEATURES

1.1Product Instructions

The newly designed H.264 / MJPEG stream IP camera provides simultaneous video codec

streams of H.264 and MJPEG in 520 TV lines. This IP camera not only supports the 25 fps frame

rate, motion detection and built-in microphone, but also the day and night, and pre- and

post-alarm functions. In addition it hosts the powerful Multi Profile function which enables the

simultaneous use of different rates of resolution while allowing two video codecs to connect with

computers at the same time. Apart from this, the camera brings you four comprehensive and

advanced user-friendly PnP operations, and captures alarm and scheduled recordings by using

an SD card. Besides, when this IP camera connecting the auto iris lens, and the IP camera makes

available the Auto Iris mode which can easily be turned on or off with the help of the switch on the

camera's side panel. In this mode the ALC function can also be activated.

This new generation H.264 network camera offers a more progressive digitalized image

technology to thoroughly update your surveillance capabilities.

1.2 Product Features

Camera:
Image sensor:	Sony 1/3 inch interlaced CCD
Image co-processor:	Sony HQ1 DSP
Minimum Illumination:	Color 0.5 lux@F1.2
	B/W 0.03 lux@F1.2
Lens type:	CS (C mount adaptor can be used)
Shutter time:	1/50~1/100,000sec (PAL)
Sensor resolution:	440K pixels (PAL)
Horizontal resolution:	520 TV lines
Auto iris type:	DC drive
Exposure:	AES/Auto-iris
S/N Ratio:	50db with AGC off
Day & Night:	Mechanical IR filter
Day & Night mode:	Auto/Day/Night/Schedule
Video Signal:
Video output type:	BNC
Video output level:	1.0 Vpp +/-10% 75Ω, composite, Negative (BNC unbalanced)
Video output frequency:	-3dB +/-1dB at 3 MHz (25 fps, best recording)
Video output burst level:	300mv(PAL) +/- 10 %
Synchronization:	Internal

4

Image 6

Contents Installation Page Table Of Contents Operating Instructions for Image Software and Network Functions of client PCSafety Precautions Product Instructions Product FeaturesVideo Signal CameraVideo Codec Mjpeg AlarmVideo Codec Video Codec H.264Hardware PowerAudio Signal ApprovalsPTZ Support Device IndicatorAccessories PortsDescription of the FRONT/REAR View Front Panel and Rear PanelAlarm I/O RS-485 D+ DC OUTDIP Switch Flank PanelNetwork Setting PPPoE USB functionInstallation Connecting with a Multiplexer UPDATE.BIN IP Camera SD card Troubleshooting PC Wiring Configuration Cable ConnectionsConnect to a computer Connect to a LAN Hub Intranet Configure Your IP Camera Network Settings Enable Dhcp FunctionSet IP Address Page TCP/IP Communication Software TCP/IP Installation TCP/IP configuration setting Select TCP/IP, and then click PropertiesConnection Testing Click Start → Programs → MS-DOS PromptType Camera IP address RJ-45 socket Connecting the IP Camera Microsoft Internet ExplorerHomepage of H.264 mode Browsing images from the IP CameraChange Image Setting Page Click the Privacy Mask button to enter the Privacy Mask Resolution Fine Tune modeDescription of function keys Change the Network Setting Description of function keys Change the Network Setting FTP Change the Network Setting Smtp Change the Network Setting Sntp Change the Network Setting Ddns Description of function keys Change the Network Setting PPPoE Change the Network Setting -UPnP Change the Network Setting IP Filter Change the Network Setting -Network Traffic Change the System Setting Set the Date and Time of the systemChange the System Setting Timestamp Change the System Setting Users Change the System Setting Digital I/O Change the System Setting Audio Mechanism Change the System Setting RS485 Setting Change the System Setting Update Firmware View the Event Logs Change the Application Setting Change the Application Setting SD Card Application Setting Change the Application Setting -SMTP Application Setting Change the Application Setting -Language Setting Description of function keys Change the Application Setting -Record Schedule Page Change the Application Setting -Motion Detection Change the SD card Setting Change the Pan/Tilt setting PPPoE & Ddns Using the PPPoE PPPoE SettingsDdns settings Test Go to the InternetSystem Requirements Introduction to the CMSInstall the CMS for the ZIP file Login the IP Camera software View the IP Camera video from a remote PCPreview the video of the IP Camera Add device Device SettingOperation Device Management Modify deviceDevice Setting Group Sequence Live ViewAdd Live View Group Delete Live View GroupRecording function PTZ Control PanelPC Playback Page DVR Remote Playback for DVR devices only Modify User ConfigUser List Add User Delete UserUser Information User Interface SettingsPath Settings User Group List Add Group UserSound Settings Image SettingsSequence Settings Record SettingsRecord Settings Setting areaWorking area Schedule barTray Tick on Enable ALARM-SAVE into SD Card to activate it QuestionSet the recording time the AVI duration of the SD card Use IE to view the recorded filesSet the PPPoE function Use the Sub Hostname to view the IP Camera Upload the recorded file via the FTPModify the user Set the upload rateAdd a new user Delete a userSpecifications Functions of client PC Appendix 1. -SCANIP Page Appendix 2. -IP Camera UPnP How To Check the IP class of your PCPage Page Install UPnP Packets Page Turn on Services Page Page Page Scan IP Cameras through My Network Place Setting the IP Address ARP and ping from Windows or MS-DOSARP and ping from Unix or GNU/Linux Set up the Ddns Registering for a Ddns Create an account101 102 103 Appendix 5. -FAQ RMN0100242v1.1