3Com DSA-3CV1001-02 service manual Précautions de sécurité concernant le VCN Access Point

Page 18

18CHAPTER 2: SAFETY INFORMATION

Précautions de sécurité concernant le VCN Access Point

Attention: Réduisez les risques d'electrocution et d'incendie

Toute intervention sera effectuée uniquement par un personnel qualifié. L'unité ne comporte pas de pièces à remplacer par l'utilisateur.

Si l'unité est visiblement endommagée ne pas la brancher au secteur, ni tenter de la mettre en fonction.

Ne pas faire fonctionner l'unité dans un endroit où la température ambiante dépasse 40 degrés C.

Assurez vous que vous avez bien débranché le câble d'alimentation électrique de la prise de courant avant d'essayer de déplacer ou de remplacer l'unité.

Le bloc d'alimentation sélectionne automatiquement la tension d'entrée (soit 100-120 V soit 200-240 V, alternatif 60/50 Hz) comme indiqué sur l'étiquette de sécurité apposé à côté de la prise. Assurez-vousque la tension disponible au secteur se trouve dans la plage appropriée.

N'employez que l'adaptateur d'alimentation fourni avec l'unité.

Sicherheitsvorkeh- rungen für den VCN Access Point

Warnung: Um das Risiko eines elektrischen Stromschlages mit möglicher Todesfolge und eines Feuers zu reduzieren:

Alle Wartungsdienste sollten nur von qualifiziertem Wartungspersonal durchgeführt werden. Die Einheit enthält keine Teile, die der Benutzer selbst warten kann.

Schließen Sie die Einheit unter keinen Umständen an das Stromnetz an, schalten diese ein oder versuchen diese zu benutzen, wenn die Einheit klar erkennbar beschädigt ist.

Bedienen Sie die Einheit nicht, wenn die Temperatur am Standort 40 Grad C übersteigt.

Ziehen Sie den Stromstecker aus der Steckdose, bevor Sie die Energieversorgung entfernen und/oder austauschen.

Image 18
Contents Visitor and Community Network Access Point 3Com Corporation 5400 Bayfront Plaza Santa Clara, California List conventions that are used throughout this guide About this GuideConventions Icon DescriptionYear RelatedDocumentation ComplianceContents Using the Local Management Access Summary and Structure of the Menus LoginOnline Technical Services World Wide Web Site 3Com FTP SitePage Visitor Features BenefitsOverview CommunityOverview Visitor Community Network Applications Shows a typical MTU/MDU applicationFeatures PBX VCN AP Software Download Network Configuration Describes the LEDs and connectors on the front panel VCN Access Point LEDs and Connectors Front ViewType State Used to Describes the connectors on the back panel VCN AP Unit LEDs and Connectors Back PanelSafety Information To reduce the risk of electrocution and firePrécautions de sécurité concernant le VCN Access Point Sicherheitsvorkeh- rungen für den VCN Access PointSicherheitsvorkehrungen für den VCN Access Point Safety Information Quantity Supplied by Installing and Operating VCN Access PointUnpacking List 3ComWall, see Installing the VCNAccess Point Under a table, seeAccess Point on a Wall Apply the paper template to the wall as shown in FigureInsert the three anchors. See Figure Drill Holes for AnchorsInserting Anchors Drive the last screw into the wall anchor to the full depth Screw Holes in the Top of the VCN APTable the lower surface of a table, as in Figure VCN AP without Curved CoverAp er tem pla te Lin e W e r Is aligned with the VCN APs small screw hole. See Figure Driving Two Screws into the TableInserting the VCN AP under the Table Completion of Mounting the VCN AP Under the Table Preparing VCN AP for Table Top Use Troubleshooting, section Power-on Self Test Post Making a Voice Call Operating the VCNVCN AP may be used for the following Any front panel connectionReceiving Data Traffic Receiving FaxesManagement Using the Local Management AccessUsing TerminalMenus Terminal EmulatorMenus use the management system efficiently Menu Hierarchy Type your Login ID and press Enter Type your password and press EnterNumber Sequence Corresponding to Submenus Return to Previous Menu Option VCN AP Main MenuVersion Screen VCN AP Management MenuEthernet Traffic Counters Ethernet Status Ethernet Traffic Count ScreenLearning Table Reset CountersChange Ethernet Work Mode Menu If a PC is not connected, the message in appearsSetting Internal Loopback Mode When you discard the operation, the message appears Setting External Loopback ModeHdlc Menu To view the Hdlc Menu Hdlc Traffic CountersType y and press Enter to perform the reset Hdlc StatusChange Hdlc Work Mode Hdlc Status ScreenNormal mode is lack of loopbacks Operation Mode Selector Menu appears Reset messages Enter FVdsl QAM Channel Status Report Set Vlan ID for Management To set the Vlan ID perform the following stepsChange Password Set Ethernet Half/Full Duplex ModeEnter the desired mode a confirmation message appears To change the password, do as followsSet to Factory Defaults Interface from the Local Management portAccess in this manual ProcedureDownload VCN Service Switch 10 Front Pane Downloading Software to the LCs in the VCN ACSoftware Download Network Configuration Software Download Menu Enter the AC Vlan ID and press Enter. The message appearsLC Downloading State Table LC Downloading Results Downloading Software to VCN APs Enter the AP Vlan ID and press Enter. The message appearsAP Downloading State Table Check Software Download for the LC Cards Download Failed for all LCs and all VCN APs Download Failed for One or More Line Cards but not AllDownload Failed for One or More VCN APs but not All Use the front panel LEDs to determine each port’s status TroubleshootingState Ethernet Line Power Determining VCN AP Status During PostVCN AP LEDs ProblemsDescribes the LEDs State IndicatesVCN AP is not VCN AP VCN AC Problem Solution Summary of VCN AP LED Indications after PostNIC Summary Abnormal Indications From Traffic Counts Hdlc Traffic Count IndicatorsSummary of Problems Indicated by Counts of Errored Frames Counter Counts the Frames Normal Count IndicatesFatal Error Messages Error message Significance User ActionAppendix a Troubleshooting Product Specification EMCAppendix B Product Specification Local Access Confirm Reset Board Management Menu appearsType Y to reset. The screen in appears Type S the downloading message appears FigureProcomm window , select Data Send File Figure Procomm Plus Terminal ScreenScreen in appears Select the correct file and click OpenWhile the file is downloading, the status window in appears Send File Status WindowFlash VCN AP LM Terminal Connector Pin Assignment PIN Assignments for LMA D CablePin No. Assignment VCN AP describes the pin assignments LM Cable Wiring LM Cable Connections MiniDIN DB-9 Pin No Pin No. AssignmentAppendix D PIN Assignments for LMA Cable To define the terminal emulation settings Terminal Emulation SettingsTerminal Emulation Settings DefiningTerminal settings can be established in one of two ways Terminal SettingsConfiguration Bar Procomm Plus SettingsProcomm Setup Window No From Left Function SettingsFlow control Connection Properties WindowTechnical Support ServicesServices Online TechnicalHours a day, 7 days a week Access by Analog ModemUsername anonymous Country Data Rate Telephone NumberAccess by Digital Modem 847 262408 727 Europe, South Africa, and Middle East Country Telephone Number Asia, Pacific RimCountry Telephone Number Fax Number Page Index NumbersRemote software download Requirements 3Com Corporation Limited Warranty Obtaining Warranty Service Ninety 90 days Governing LAWEMC Statements