3Com DSA-3CV1001-02 service manual Downloading Software to the LCs in the VCN AC

Page 59

Remote Software Download

59

Downloading Software to the LCs in the VCN AC

1Remove the cover of the LMA section of the VCN AP to reveal the LMA port, as shown in page 38, Figure 27.

2Connect the management computer to the VCN AP LMA port.

3Using RJ-45 connectors, connect the Ethernet port of the VCN AP to an Ethernet switch 10BaseT port; refer to Figure 53. Refer to Figure 54 for the network configuration.

Recommendation: Attach the downloading VCN AP to port

■26 in the VCN Services Switch 10.

■26 in the the SuperStack II Switch 1100.

■24 in the VCN Services Switch 100.

■24 in the SuperStack II Switch 3300.

Figure 53 The VCN Service Switch 10 Front Pane

1x

13x

6x 7x

18x 19x

12x

24x


				g re e n		= enabled, link O K
		flashing green				= disabled, link O K
					off	= link fail
T C V R 1	2	3	4	5	6	7	8	9	1 0	11	1 2		P acket
1	2	3	4	5	6	7	8	9	1 0	11	1 2		S tatus
1 3	1 4	1 5	1 6	1 7	1 8 1 9		2 0	2 1 2 2		2 3	2 4		P acket
1 3	1 4	1 5	1 6	1 7	1 8 1 9		2 0	2 1 2 2		2 3	2 4		S tatus

3 C V 2 0 1 0

			1	2
			3	4
	25	26 P acket	5	6	Power/Self Test
	25	26 S tatus	7	8
2 5 x	2 6 x				VC N Services
					Sw itch 10

Image 59

Contents Visitor and Community Network Access Point 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Icon Description About this GuideConventions List conventions that are used throughout this guideCompliance RelatedDocumentation YearContents Summary and Structure of the Menus Login Using the Local Management Access3Com FTP Site Online Technical Services World Wide Web SitePage Community Features BenefitsOverview VisitorOverview Shows a typical MTU/MDU application Visitor Community Network ApplicationsFeatures PBX VCN AP Software Download Network Configuration Type State Used to Describes the LEDs and connectors on the front panelVCN Access Point LEDs and Connectors Front View VCN AP Unit LEDs and Connectors Back Panel Describes the connectors on the back panelTo reduce the risk of electrocution and fire Safety InformationSicherheitsvorkeh- rungen für den VCN Access Point Précautions de sécurité concernant le VCN Access PointSicherheitsvorkehrungen für den VCN Access Point Safety Information 3Com Installing and Operating VCN Access PointUnpacking List Quantity Supplied byUnder a table, see Installing the VCNAccess Point Wall, seeApply the paper template to the wall as shown in Figure Access Point on a WallDrill Holes for Anchors Insert the three anchors. See FigureInserting Anchors Screw Holes in the Top of the VCN AP Drive the last screw into the wall anchor to the full depthVCN AP without Curved Cover Table the lower surface of a table, as in FigureAp er tem pla te Lin e W e r Driving Two Screws into the Table Is aligned with the VCN APs small screw hole. See FigureInserting the VCN AP under the Table Completion of Mounting the VCN AP Under the Table Preparing VCN AP for Table Top Use Troubleshooting, section Power-on Self Test Post Any front panel connection Operating the VCNVCN AP may be used for the following Making a Voice CallReceiving Faxes Receiving Data TrafficTerminal Using the Local Management AccessUsing ManagementMenus use the management system efficiently MenusTerminal Emulator Menu Hierarchy Number Sequence Corresponding to Submenus Type your Login ID and press EnterType your password and press Enter VCN AP Main Menu Return to Previous Menu OptionVCN AP Management Menu Version ScreenEthernet Traffic Counters Ethernet Traffic Count Screen Ethernet StatusIf a PC is not connected, the message in appears Reset CountersChange Ethernet Work Mode Menu Learning TableSetting Internal Loopback Mode Setting External Loopback Mode When you discard the operation, the message appearsHdlc Traffic Counters Hdlc Menu To view the Hdlc MenuHdlc Status Type y and press Enter to perform the resetHdlc Status Screen Change Hdlc Work ModeNormal mode is lack of loopbacks Operation Mode Selector Menu appears Enter F Reset messagesVdsl QAM Channel Status Report To set the Vlan ID perform the following steps Set Vlan ID for ManagementTo change the password, do as follows Set Ethernet Half/Full Duplex ModeEnter the desired mode a confirmation message appears Change PasswordInterface from the Local Management port Set to Factory DefaultsDownload Access in this manualProcedure Downloading Software to the LCs in the VCN AC VCN Service Switch 10 Front PaneSoftware Download Network Configuration Enter the AC Vlan ID and press Enter. The message appears Software Download MenuLC Downloading State Table LC Downloading Results Enter the AP Vlan ID and press Enter. The message appears Downloading Software to VCN APsAP Downloading State Table Check Software Download for the LC Cards Download Failed for One or More Line Cards but not All Download Failed for all LCs and all VCN APsDownload Failed for One or More VCN APs but not All Determining VCN AP Status During Post TroubleshootingState Ethernet Line Power Use the front panel LEDs to determine each port’s statusState Indicates ProblemsDescribes the LEDs VCN AP LEDsVCN AP is not VCN AP VCN AC Summary of VCN AP LED Indications after Post Problem SolutionNIC Counter Counts the Frames Normal Count Indicates Hdlc Traffic Count IndicatorsSummary of Problems Indicated by Counts of Errored Frames Summary Abnormal Indications From Traffic CountsError message Significance User Action Fatal Error MessagesAppendix a Troubleshooting EMC Product SpecificationAppendix B Product Specification Local Access Management Menu appears Confirm Reset BoardType S the downloading message appears Figure Type Y to reset. The screen in appearsProcomm Plus Terminal Screen Procomm window , select Data Send File FigureSelect the correct file and click Open Screen in appearsSend File Status Window While the file is downloading, the status window in appearsFlash VCN AP Pin No. Assignment LM Terminal Connector Pin AssignmentPIN Assignments for LMA D Cable VCN AP describes the pin assignments MiniDIN DB-9 Pin No Pin No. Assignment LM Cable Wiring LM Cable ConnectionsAppendix D PIN Assignments for LMA Cable Defining Terminal Emulation SettingsTerminal Emulation Settings To define the terminal emulation settingsProcomm Plus Settings Terminal SettingsConfiguration Bar Terminal settings can be established in one of two waysNo From Left Function Settings Procomm Setup WindowConnection Properties Window Flow controlOnline Technical ServicesServices Technical SupportCountry Data Rate Telephone Number Access by Analog ModemUsername anonymous Hours a day, 7 days a week408 727 Access by Digital Modem847 262 Country Telephone Number Asia, Pacific Rim Europe, South Africa, and Middle EastCountry Telephone Number Fax Number Page Numbers IndexRemote software download Requirements 3Com Corporation Limited Warranty Obtaining Warranty Service Governing LAW Ninety 90 daysEMC Statements