Kenwood G-EQ300 Operation in GRAPHIC mode, 2 5 K H Z, Select the “GRAPHIC” mode, Adjust its level

Page 17

Operation in GRAPHIC mode

This mode allows to adjust the equalizer curve for each frequency band provided. The curve created in the param- eter mode can be fine-adjusted in this mode.

Creation of desired equalizer patterns

G-EQ300 (En/K)

1 7

Operation in GRAPHIC mode

1Select the “graphic equalizer display mode”.

Each press switches the display modes as follows.

DISPLAY		1 Graphic equalizer display mode

2 Spectrum analyzer display mode

3 DEMO(Demonstration) mode

2Select the “EQ.ON” mode.

EQ.EFFECT

3Select the “GRAPHIC” mode.

GRAPHIC/

PARAMETRIC

4Select the frequency band to be adjusted.

FREQUENCY JOG

“EQ. ON” lights up.

EQ. ON

Each press switches the display as follows.

1 GRAPHIC

: Mode for adjusting equalizer curves.

2PARAMETRIC: Mode for creating a curve according to center frequencies.

“GRAPHIC” lights up.

GRAPHIC

2 5 K H Z

5Adjust its level.

EQ.LEVEL

1k 1.5k 2.5k 3.9k 6.3k

6Fine adjustment of each frequency band:

Repeat steps 4 and 5 above.

If the mode is switched from “GRAPHIC” to “PARAMETRIC”, the equalizer pattern created in the GRAPHIC mode is cleared.

Note

Image 17

Contents INSTRUCTION MANUAL G-EQ300KENWOOD CORPORATION GRAPHIC EQUALIZER2 Before applying power Safety precautionsAC 110-120 / 220-240 V switchable AC voltage selector switchContents Special featuresAccessories Check that the following accessories are present3Caution Read this page carefully to ensure safe operation IMPORTANT SAFEGUARDSPOWER OFF IMPORTANT SAFEGUARDSCleaning MaintenanceBefore operation Unpacking1 MAIN POWER key Switch the unit ON mode 2 ON/STANDBY key STANDBY indicator3 Standby indicator 5 TAPE indicatorSet the TAPE 2 MONITOR switch to the monitoring position Caution regarding placement Except for U.S.A., CanadaSystem connections 8 manuals of the related componentsRemote Control AV CONTROL CENTER POWER AMPLIFIER GRAPHIC EQUALIZER CASSETTE DECKAbout the system control connections About the system control operationsDisplay Switching the display modesPreparation Graphic equalizer display mode1 Play a music source 2 Select the “DEMO” mode Demonstration methodTo stop demonstration To cancel the equalizer effect Operation of MANUAL featureOperation of graphic equalizer “FLAT” keyFive exemplary patterns have been preset at the factory Operation of REFERENCE feature3 Set to “REFERENCE” Operation of graphic equalizerPreset equalizer pattern R1 to R5 Preset equalizer pattern M1 to M5Pattern can be created and preset by the user in this mode M5 HeadphonesOperation in PARAMETRIC mode Creation of desired equalizer patterns1 Select the “graphic equalizer display mode” 2 Select the “EQ.ON” mode9 8 H Z 6 Adjust the level5 Select the center frequency 7 Select the inclination of the curve5 Adjust its level 4 Select the frequency band to be adjusted6 Fine adjustment of each frequency band Operation in GRAPHIC mode2Preset the equalizer pattern To cancel the registered patternAny equalizer pattern can be preset if it is being dis- played Registration of EQUALIZER pattern3 Select the genre of music 1 Play a music source 2 Initiate the GENRE mode4 Select the desired tone pattern The five of the genre keys are also used as the pattern No. keysREVERSE key To cancel GENRE mode5 Select the purpose of use of the pattern Major purposes of use provided by the USE keysUse of equalizer effect with tape 1 Set the TAPE switch to ONApplying equalizer effect to tape playback To stop tape playbackTape recording of sound with equalizer effect 1 Set the TAPE switch to OFFTo stop tape recording 4 Play the source to be recorded 5 Start recording it onto tapeAdjustment of sound to your individual taste Compensation for the audio characteristics of the listening roomFunctions of the graphic equalizer Functions of graphic equalizerSymptom Operation to resetIn case of difficulty CauseSignal to noise ratio IHF SpecificationsGraphic equalizer characteristics Equalizer characteristic variable rangeFor the U.S.A FCC WARNING MEMO Serial Number For your recordsModel