Kenwood G-EQ300 Introduction, Safety precautions, Before applying power, AC voltage selection

Page 2
Introduction

Introduction

2 Before applying power

G-EQ300 (En/K)

Caution : Read this section carefully to ensure safe operation.

 

 

 

 

 

 

 

 

 

Units are designed for operation as follows.

 

 

U.S.A. and Canada

AC 120 V only

 

Australia

AC 240 V only

 

China

AC 220 V only

 

U.K. and Europe

AC 230 V only

 

*Other countries

AC 110-120 / 220-240 V switchable
*AC voltage selection

The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

 

Note:

 

Our warranty does not cover damage caused by excessive

Note

line voltage due to improper setting of the AC voltage

selector switch.

 

AC voltage selector switch

VOLTAGE SELECTOR

AC 110 - 120V ‘ AC 220 - 240V ‘

VOLTAGE SELECTOR

AC 110 - 120V ‘ AC 220 - 240V ‘

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

For the United Kingdom
Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 13- Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appro priate safety approved extension lead or adapter, or consult your dealer.If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT :

The wires in the mains lead are coloured in accordance with the following code :

Blue: Neutral

Brown : Live

Do not connect those leads to the earth terminal of a three - pin plug.

Safety precautions

Caution : Read this section carefully to ensure safe operation.

 

 

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents KENWOOD CORPORATION G-EQ300INSTRUCTION MANUAL GRAPHIC EQUALIZERAC 110-120 / 220-240 V switchable Safety precautions2 Before applying power AC voltage selector switchAccessories Special featuresContents Check that the following accessories are presentIMPORTANT SAFEGUARDS 3Caution Read this page carefully to ensure safe operationIMPORTANT SAFEGUARDS POWER OFFBefore operation MaintenanceCleaning Unpacking3 Standby indicator STANDBY indicator1 MAIN POWER key Switch the unit ON mode 2 ON/STANDBY key 5 TAPE indicatorSystem connections Caution regarding placement Except for U.S.A., CanadaSet the TAPE 2 MONITOR switch to the monitoring position 8 manuals of the related componentsAbout the system control connections AV CONTROL CENTER POWER AMPLIFIER GRAPHIC EQUALIZER CASSETTE DECKRemote Control About the system control operationsPreparation Switching the display modesDisplay Graphic equalizer display mode1 Play a music source 2 Select the “DEMO” mode Demonstration methodTo stop demonstration Operation of graphic equalizer Operation of MANUAL featureTo cancel the equalizer effect “FLAT” key3 Set to “REFERENCE” Operation of REFERENCE featureFive exemplary patterns have been preset at the factory Operation of graphic equalizerPattern can be created and preset by the user in this mode Preset equalizer pattern M1 to M5Preset equalizer pattern R1 to R5 M5 Headphones1 Select the “graphic equalizer display mode” Creation of desired equalizer patternsOperation in PARAMETRIC mode 2 Select the “EQ.ON” mode5 Select the center frequency 6 Adjust the level9 8 H Z 7 Select the inclination of the curve6 Fine adjustment of each frequency band 4 Select the frequency band to be adjusted5 Adjust its level Operation in GRAPHIC modeAny equalizer pattern can be preset if it is being dis- played To cancel the registered pattern2Preset the equalizer pattern Registration of EQUALIZER pattern4 Select the desired tone pattern 1 Play a music source 2 Initiate the GENRE mode3 Select the genre of music The five of the genre keys are also used as the pattern No. keys5 Select the purpose of use of the pattern To cancel GENRE modeREVERSE key Major purposes of use provided by the USE keysApplying equalizer effect to tape playback 1 Set the TAPE switch to ONUse of equalizer effect with tape To stop tape playbackTo stop tape recording 1 Set the TAPE switch to OFFTape recording of sound with equalizer effect 4 Play the source to be recorded 5 Start recording it onto tapeFunctions of the graphic equalizer Compensation for the audio characteristics of the listening roomAdjustment of sound to your individual taste Functions of graphic equalizerIn case of difficulty Operation to resetSymptom CauseGraphic equalizer characteristics SpecificationsSignal to noise ratio IHF Equalizer characteristic variable rangeFor the U.S.A FCC WARNING MEMO Serial Number For your recordsModel
Top Page Image Contents