Kenwood G-EQ300 System connections, Caution regarding placement Except for U.S.A., Canada

Page 8

System connections

System connections

Make connection as shown below. When connecting the related system components, refer also to the instruction

8 manuals of the related components.

3Caution: Do not plug in the power lead until all connec- tions are completed.

G-EQ300 (En/K)

Malfunction of microprocessor

If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microprocessor referring to “In case of difficulty”.

¢

Caution regarding placement ( Except for U.S.A., Canada )

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below.

Left and right panels: 10 cm, rear panel: 10 cm

AV CONTROL CENTER

*CAUTION (For U.K.)

When using the AC outlet epuipped with this unit, be sure to consult your dealer for the correspond-ing plug.

TAPE 2

(MONITOR)

L

R

REC PLAY

SYSTEM

CONTROL

Connect to the TAPE 2 (MONITOR) jacks

Set the TAPE 2 (MONITOR ) switch to the monitoring position.

*

U.K.

Australia

U.S.A., Canada,

China and US military

Other countries

Audio cords

TAPE		LINE	SYSTEM
PLAY	REC		SYSTEM
IN	OUT	IN OUT	CONTROL
L			L
R			R

To wall

AC outlet

AC

System control cord

Audio cords

LINE

REC PLAY

IN OUT

L

R

This unit

Cassette tape deck (optional)

Use the numbers 9 0 ! @on the rear panel of this unit when connecting it to an AV CONTROL CENTER or

RECEIVER.

Connections are easily completed by using Audio cords to make connections to the same numbers on the other component.

÷When a cassette deck is connected to the graphic equalizer,do not connect the system control cord to the cassette deck.

÷When connecting the audio cords (cords with pin plugs on each end), insert the white plugs into the L(Left) jacks and red plugs into the R (Right) jacks.

1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced.

Notes 2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage on the unit.

3. Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit.

Image 8

Contents G-EQ300 INSTRUCTION MANUALKENWOOD CORPORATION GRAPHIC EQUALIZERSafety precautions 2 Before applying powerAC 110-120 / 220-240 V switchable AC voltage selector switchSpecial features ContentsAccessories Check that the following accessories are presentIMPORTANT SAFEGUARDS 3Caution Read this page carefully to ensure safe operationIMPORTANT SAFEGUARDS POWER OFFMaintenance CleaningBefore operation UnpackingSTANDBY indicator 1 MAIN POWER key Switch the unit ON mode 2 ON/STANDBY key3 Standby indicator 5 TAPE indicatorCaution regarding placement Except for U.S.A., Canada Set the TAPE 2 MONITOR switch to the monitoring positionSystem connections 8 manuals of the related componentsAV CONTROL CENTER POWER AMPLIFIER GRAPHIC EQUALIZER CASSETTE DECK Remote ControlAbout the system control connections About the system control operationsSwitching the display modes DisplayPreparation Graphic equalizer display mode1 Play a music source 2 Select the “DEMO” mode Demonstration methodTo stop demonstration Operation of MANUAL feature To cancel the equalizer effectOperation of graphic equalizer “FLAT” keyOperation of REFERENCE feature Five exemplary patterns have been preset at the factory3 Set to “REFERENCE” Operation of graphic equalizerPreset equalizer pattern M1 to M5 Preset equalizer pattern R1 to R5Pattern can be created and preset by the user in this mode M5 HeadphonesCreation of desired equalizer patterns Operation in PARAMETRIC mode1 Select the “graphic equalizer display mode” 2 Select the “EQ.ON” mode6 Adjust the level 9 8 H Z5 Select the center frequency 7 Select the inclination of the curve4 Select the frequency band to be adjusted 5 Adjust its level6 Fine adjustment of each frequency band Operation in GRAPHIC modeTo cancel the registered pattern 2Preset the equalizer patternAny equalizer pattern can be preset if it is being dis- played Registration of EQUALIZER pattern1 Play a music source 2 Initiate the GENRE mode 3 Select the genre of music4 Select the desired tone pattern The five of the genre keys are also used as the pattern No. keysTo cancel GENRE mode REVERSE key5 Select the purpose of use of the pattern Major purposes of use provided by the USE keys1 Set the TAPE switch to ON Use of equalizer effect with tapeApplying equalizer effect to tape playback To stop tape playback1 Set the TAPE switch to OFF Tape recording of sound with equalizer effectTo stop tape recording 4 Play the source to be recorded 5 Start recording it onto tapeCompensation for the audio characteristics of the listening room Adjustment of sound to your individual tasteFunctions of the graphic equalizer Functions of graphic equalizerOperation to reset SymptomIn case of difficulty CauseSpecifications Signal to noise ratio IHFGraphic equalizer characteristics Equalizer characteristic variable rangeFor the U.S.A FCC WARNING MEMO Serial Number For your recordsModel