Kenwood G-EQ300 In case of difficulty, Operation to reset, Symptom, Cause, Remedy

Page 24

In case of difficulty

In case of difficulty

G-EQ300 (En/K)

What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative.

2 4

Operation to reset

The microprocessor may fall into malfunction (impossibility to operate erroneous display, etc.) when the power cord is unplugged while power is ON or due to an external factor. In this case, execute the following procedure to reset the microprocessor and return it to normal condition.

While pressing and holding the MEMORY key, press the MAIN POWER switch to OFF then ON again.

●Please note that resetting the microprocessor clears the contents stored in, it returns the micro- processor to the condition when it left the factory.

Symptom	Cause	Remedy
Power fails to turn on.	¦The power cord is plugged incompletely.	¦Insert the power plug securely into the power
		outlet.
	¦The system control cord is not connected.	¦Connect the cord properly by referring to “Sys-
		tem connections“.	8

The equalizer effect cannot be obtained.	¦The input and output connections are reversed.	¦Connect the input and output correctly.	8

Image 24

Contents G-EQ300 INSTRUCTION MANUALKENWOOD CORPORATION GRAPHIC EQUALIZERSafety precautions 2 Before applying powerAC 110-120 / 220-240 V switchable AC voltage selector switchSpecial features ContentsAccessories Check that the following accessories are presentIMPORTANT SAFEGUARDS 3Caution Read this page carefully to ensure safe operationIMPORTANT SAFEGUARDS POWER OFFMaintenance CleaningBefore operation UnpackingSTANDBY indicator 1 MAIN POWER key Switch the unit ON mode 2 ON/STANDBY key3 Standby indicator 5 TAPE indicatorCaution regarding placement Except for U.S.A., Canada Set the TAPE 2 MONITOR switch to the monitoring positionSystem connections 8 manuals of the related componentsAV CONTROL CENTER POWER AMPLIFIER GRAPHIC EQUALIZER CASSETTE DECK Remote ControlAbout the system control connections About the system control operationsSwitching the display modes DisplayPreparation Graphic equalizer display modeDemonstration method To stop demonstration1 Play a music source 2 Select the “DEMO” mode Operation of MANUAL feature To cancel the equalizer effectOperation of graphic equalizer “FLAT” keyOperation of REFERENCE feature Five exemplary patterns have been preset at the factory3 Set to “REFERENCE” Operation of graphic equalizerPreset equalizer pattern M1 to M5 Preset equalizer pattern R1 to R5Pattern can be created and preset by the user in this mode M5 HeadphonesCreation of desired equalizer patterns Operation in PARAMETRIC mode1 Select the “graphic equalizer display mode” 2 Select the “EQ.ON” mode6 Adjust the level 9 8 H Z5 Select the center frequency 7 Select the inclination of the curve4 Select the frequency band to be adjusted 5 Adjust its level6 Fine adjustment of each frequency band Operation in GRAPHIC modeTo cancel the registered pattern 2Preset the equalizer patternAny equalizer pattern can be preset if it is being dis- played Registration of EQUALIZER pattern1 Play a music source 2 Initiate the GENRE mode 3 Select the genre of music4 Select the desired tone pattern The five of the genre keys are also used as the pattern No. keysTo cancel GENRE mode REVERSE key5 Select the purpose of use of the pattern Major purposes of use provided by the USE keys1 Set the TAPE switch to ON Use of equalizer effect with tapeApplying equalizer effect to tape playback To stop tape playback1 Set the TAPE switch to OFF Tape recording of sound with equalizer effectTo stop tape recording 4 Play the source to be recorded 5 Start recording it onto tapeCompensation for the audio characteristics of the listening room Adjustment of sound to your individual tasteFunctions of the graphic equalizer Functions of graphic equalizerOperation to reset SymptomIn case of difficulty CauseSpecifications Signal to noise ratio IHFGraphic equalizer characteristics Equalizer characteristic variable rangeFor the U.S.A FCC WARNING MEMO For your records ModelSerial Number