Blaupunkt RCM 104 operating instructions Deactivating the TIM standby mode, If you are sure

Page 16

 

 

 

 

adjusted

 

 

 

start

TIM-TIME

 

end

 

 

 

1.5 hours

 

 

1.5 hours

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The motor antenna will be extracted

Use the rocker button / to choose TIM-TIME in the DSC menu.

Press << or >> to call up the adjusted time.

If TIM OFF is displayed, the TIM function is deactivated.

Use the rocker button / to set the time.

Use << to move to the hours or >> to adjust the minutes.

Confirm your entry by

pressing -dBor DSC. The TIM-TIME is stored.

TIM will be active 1.5 hours before and after the adjusted TIM-TIME.

Also, TIM will automatically stay on standby for three hours after the radio was turned off. When TIM is activated, the display will briefly show “TIM ON” when the set is switched off.

Deactivating the TIM standby mode

Press DSC with the radio being turned on.

Use the / rocker button to select the item TIM TIME.

Press -dBand switch to TIM OFF with rocker button / (you find this item between the time settings for 23:00 and 0:00).

When TIM OFF is flashing,

press DSC or -dB.

If the motor antenna is retracted immediately after selecting TIM OFF, you can be assured that the TIM function is deactivated.

Warning

The motor antenna could be damaged in a car wash.

If you have a motor antenna installed, it will remain extracted after you have turned off the radio with the TIM function being activa- ted. The antenna may also be extracted in the car wash when the set is turned off and the TIM function activated.

TIM is deactivated (TIM OFF), if the motor antenna is retracted as soon as the set is turned off.

You can now drive through a car wash when the radio is off.

Do not switch on the radio until you have left the car wash.

If the display shows TIM ON when switching off the radio, then the TIM timer is activated. The motor antenna will remain extracted.

If you are sure,

that now and while being in the car wash you are outside the recording period around the adjusted TIM-TIME:

 

 

 

 

adjusted

 

 

 

 

start

TIM-TIME

 

end

 

 

 

1.5 hours

 

 

1.5 hours

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The motor antenna will be extracted

Switch off the radio and press TIM. The display briefly shows STBY OFF.

The antenna will then remain retracted when the radio is turned off (until the three-hour recording period starts).

Attention:

You should by all means deactivate the TIM timer (TIM OFF), if the adjusted recor- ding period is soon to start.

For this purpose:

Press DSC with the radio being activa- ted.

Use the / rocker button to select the item TIM TIME.

38

Image 16
Contents Frankfurt RCM 15 14 Table of contents Switching on Switching offQuick instructions FMTDSC Mode AF ModeCPS AUD3, 4, 5, 6 preset buttons PTY buttonTIM/TA ? BC Dolby NRTape side selector To change the seek tuning sensitiviMIX Traffic safety Installation/connectionImportant notes What you really have to readSelecting the operating mode Speech programs, Beep volume, SCANTI- ME, VolfixInsert KeyCard 1 and switch the radio on KeyCardAutomatic seek tuning Radio operation with RDS Radio Data SystemAF Alternative Frequency REG RegionalAdjusting the seek tuning sensi- tivity Stereo mono switch FMChanging the memory bank FM Storing stationsRecalling stored stations Preset scanningScanning stations with Radio Scan Station naming Automatic seek tuning start Adjusting the traffic message volumeSwitching the warning beep off Traffic announcement priority on/offTraffic Memo TIM Do not switch on the radio until you have left the car wash Deactivating the TIM standby modeIf you are sure Inserting a tape RT RadiotextRemoving a tape Fast forward/rewind AutoreverseTape type detection Scanning cassette titlesSkipping unrecorded tape sec- tions with BLS Blank Skip DSC programmingCare of your audio equipment Time CDC NameAngle BAS F=RPTY Lang PTY SETSpeech ScantimeSwitching the CD mode on Using SRC of the car radioSelecting a CD/track using the rocker switch CD changer control optionDeleting CD names Entering/displaying CD namesPrecondition Name must be selected under Technical data Survey of DSC default settingsAppendix
Related manuals
Manual 20 pages 46.37 Kb