Blaupunkt RCM 104 Quick instructions, Switching on, Switching off, Fmt, Extra function

Page 4

Quick instructions

1Switching on:

Hold down the ON button (the KeyCard has to be inserted), the set plays with the pre-adjusted volume.

Switching off:

Press ON for approximately 1 second. If the set was turned on by pressing ON, the KeyCard can be used for swit- ching the system on and off. Please read the information of chapter “Key- Card”.

The set may also be turned off via the vehicle’s ignition (provided that it was connected correspondingly). After the ignition was switched off, a double beep tone reminds you that you should remove the KeyCard before leaving your vehicle.

To operate the set when the ignition is switched off (KeyCard is inserted), pro- ceed as follows:

Press “ON” after the double beep tone. The set will be turned on.

To avoid that the battery goes flat, the system will be turned off automatically after a playback time of one hour.

2To change the volume: Press VOL+/VOL-.

Each time the set is switched on, it will play with the pre-adjusted volume (VOL FIX). You may also change the VOL FIX setting (see chapter “DSC pro- gramming“).

3FMT

Press this button to switch between the memory banks I, II, and T (Travelstore). As soon as this button is pressed, the system will automatically switch to FM.

Extra function:

Store the six most powerful stations automatically with Travelstore: Press FMT until seek tuning starts in the display.

4M•L

To change between medium wave (MW) and long wave (LW) frequencies.

5-dB- for instantly changing the volume Press the -dBbutton to instantly mute the audio source. The display will then show MUTE. Return to normal volume by pressing either the -dBor the VOL+ button.

When pressing VOL-, the normal play- back volume is identical to the -dB(mu- ted) volume.

To program the mute volume, proceed as follows:

•Adjust the desired volume.

•Press -dBfor approximately 2 se- conds (beep tone is released).

This volume will then be stored as the mute volume.

Extra function:

Press this button to store the values set in the DSC menu.

26

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Frankfurt RCM 15 14 Table of contents Switching on Switching offQuick instructions FMTDSC Mode AF ModeCPS AUD3, 4, 5, 6 preset buttons PTY buttonTIM/TA ? BC Dolby NRTape side selector To change the seek tuning sensitiviMIX Traffic safety Installation/connectionImportant notes What you really have to readSelecting the operating mode Speech programs, Beep volume, SCANTI- ME, VolfixInsert KeyCard 1 and switch the radio on KeyCardAutomatic seek tuning Radio operation with RDS Radio Data SystemAF Alternative Frequency REG RegionalAdjusting the seek tuning sensi- tivity Stereo mono switch FMChanging the memory bank FM Storing stationsRecalling stored stations Preset scanningScanning stations with Radio Scan Station naming Automatic seek tuning start Adjusting the traffic message volumeSwitching the warning beep off Traffic announcement priority on/offTraffic Memo TIM Do not switch on the radio until you have left the car wash Deactivating the TIM standby modeIf you are sure Inserting a tape RT RadiotextRemoving a tape Fast forward/rewind AutoreverseTape type detection Scanning cassette titlesSkipping unrecorded tape sec- tions with BLS Blank Skip DSC programmingCare of your audio equipment Time CDC NameAngle BAS F=RPTY Lang PTY SETSpeech ScantimeSwitching the CD mode on Using SRC of the car radioSelecting a CD/track using the rocker switch CD changer control optionDeleting CD names Entering/displaying CD namesPrecondition Name must be selected under Technical data Survey of DSC default settingsAppendix
Related manuals
Manual 20 pages 46.37 Kb
Top Page Image Contents