Blaupunkt RCM 126 operating instructions Receiving traffic programme stations with RDS-EON, On/off

Page 19

Receiving traffic programme stations with RDS-EON

The abbreviation “EON” stands for En-

Traffic announcement priority

Warning beep

hanced

Other Networks, meaning the

on/off

If you leave the reception area of the traffic

exchange of information within a radio net-

 

If the priority for traffic announcement pro-

programme station currently tuned into, you

work.

 

 

grammes is activated, “TA” will light up in will hear a warning beep after approximate-

Many FM broadcasters offer traffic messag-

the display.

ly 30 seconds.

es for their service area at regular intervals.

To switch the priority on or off:

This alarm tone will also be released when

All traffic

programme stations transmit a

pressing a preset button which has no traf-

• Press TIM for approximately two sec-

special carrier signal alongside their pro-

fic programme allocated to it.

grammes, which is decoded by your car ra-

onds until you hear a beep.

 

dio. If this signal is identified, “TP” will ap-

When pressing TIM while a message is be-

Switching the warning beep off

pear in the display (Traffic Programme).

ing broadcast, this message will be interrup-

a) Tune into another station offering traf-

In addition to these, there are also stations

ted. The unit will then switch back to the pre-

which do not actually transmit traffic pro-

vious condition, though the recording of this

fic information:

grammes themselves, but by using RDS-

message in the TIM memory will remain

• Press the rocker switch or

EON they offer the possibility to receive the

uninterrupted.

• press a preset button which has a

traffic messages broadcast by another traf-

If you press the TIM button once again,

traffic programme station allocated

fic programme station in the same radio

“RECORD” will appear in the display for

to it.

network.

 

approximately two seconds.

 

Alternatively:

If you wish to have the priority for traffic an-

When interrupting an EON message, the

b) Switch off the priority for traffic an-

nouncements activated while listening to

radio will not continue to record the an-

nouncements:

one of these stations (e.g. NDR3), “TA” must

nouncement since it will switch back to the

• Press TIM for approximately two

appear on the display panel.

programme heard before.

If a traffic announcement is broadcast, the

The priority for other traffic messages re-

seconds until you hear a beep.

radio will automatically switch to the linked

mains active.

“TA” will disappear from the dis-

traffic programme station (in this case,

Please note that several buttons have no

play.

NDR2) for the duration of the message and

function while a traffic announcement is

 

return to the original programme (NDR3)

broadcast.

 

afterwards.

 

 

48

Image 19
Contents Köln RCM Page Contents FMT Quick referenceExtra rocker switch functions Rocker switchAUD J GEO DSC Mode H PTY Flashing KeyCard tongue DisplayMIX OFF MIXMIX CD MIX MAG@ DIS Extra function GEO AUDImportant notes Never pull out the KeyCard directly KeyCard theft protection systemRemoving the KeyCard Replacing a KeyCardTurn On Message T.O.M Switching off the flashlightCare of your KeyCard Radio operation with RDS Radio Data System Storing stations Manual tuning withScrolling through the broadcast- ing networks only FM Changing the memory bank FMChanging the scan time To start Preset ScanTo select a scanned station and switch Off Preset ScanProgramme type Switching from stereo to mono FMNews Scanning stations with PTY-SCAN Storing programme typesPTY priority Radiotext On/off Switching the warning beep offReceiving traffic programme stations with RDS-EON Traffic announcement priorityTo make a setting Automatic seek tuning startTraffic Memo TIM Programming the TIM standby mode / TIM timesMenu Recalling stored traffic messag- es Deactivating the TIM standby modeTIM standby mode while the ra Dio is switched offBefore driving into a car wash Temporarily interrupting the TIM standby modeTape operation Dolby BC NR Tions with Blank SkipMIX playback Switching to CDC operationCD changer operation optional Selecting CDs and titlesScan operation Selecting the display mode Storing the display modeTo stop the Scan function Deleting CD names with DSC-UPDATEDSC programming Colour To quit the DSC programming mode and store the adjustment Overview of the DSC factory settingsAUX Tape player SpecificationsAppendix TunerBosch Gruppe
Related manuals
Manual 31 pages 21.97 Kb Manual 27 pages 5.33 Kb