Blaupunkt RDM 127 operating instructions Local, Store Exit, By station search or manually

Page 19

Note:

If a station is displayed but crossed out in the preference menu, this means that either the reception is very poor or that the station could not be clearly identified as the one stored.

Stations on the same frequency which do not transmit an RDS signal cannot be clearly differentiated from one another.

. . . by station search or manually

You must select the station search menu first.

You can switch from the reception or preference table

•by pressing SEARCH.

The search menu has been selected when SCAN appears in the upper left cor- ner of the display.

Start the station search function by pressing

• (up) or (down).

The station search will stop at the next station within reception range.

The station search sensitivity selected LOCAL or DX (distant) will be highlighted in the display.

•You can toggle between the two levels of station search sensitivity by pressing the corresponding softkey .

The station search sensitivity can be set separately for LOCAL and DX. For more information refer to the section on “Programming with DSC – TUNER, S-LO or S-DX”.

If you hold down /, the station search will run forwards or backwards quickly.

Start the manual station search by pressing << or >>, the frequency will move up or down in increments.

If you hold << or >> down, then the frequencies will run through quickly.

S

NDR 2

SEARCH		BREMEN 3
SCAN		HR 3
D-Radio		NDR1 NDS
BREMEN 1		NDR	2
BREMEN 2		NDR	3

S

NDR 2 92.10

SCAN

LOCAL

DX

STORE

EXIT

19

DEUTSCH	ENGLISH	FRANÇAIS	ITALIANO	NEDERLANDS	SVENSKA	ESPAÑOL	PORTUGUÊS

Image 19

Contents New York RDM Traffic safety Table of contentsImportant information PrecautionsInstallation AccessoriesOptional Remote control RCQuick reference On / Mute Switching on/offCDC CD changer TU tunerDisplay header Display/Selection menuCD eject Open/close panel. Eject/insert CD Softkeys Tons optional Radio mode = Multi-functional rocker switch or remote control butAdditional functions for the rocker switch Flashing KeyCard tongue Inserting the KeyCardStarting up the unit KeyCard anti-theft systemTraining the second KeyCard / replacing the KeyCard Removing the KeyCardDSC-MAIN Menu Short Additional Memory S.A.M Displaying the radio pass dataTurn On Message T.O.M Optical indication of anti-theft protection Switching off the flashing lightTaking care of your KeyCard Detailed operating instructions First-time installationFirst Install Clock OWNER-ID AUX-IN Norm SET Exit Setting the clockAUX OWNER-ID Clear Exit First InstallAUX-NAME Exit L K M a N Clear Exit Resetting to original factory settings Radio operation with RDS Radio Data System Switching to the radio modeSelecting the waveband NDR1 NDS Switching from the reception table to the preference tableSelecting a station NDRStart the station search function by pressing LocalStore Exit By station search or manuallyEnd Scan A NWith Scan Start ScanSelect reception table to store stations Storing stationsStore Exit NDR Search Bremen Scan FM stationsSelect search menu to store stations Deleting stored stationLocal DX Store Storing MW/LW stationsAlternative frequency Station nameSearch Scan Antenne NDR2 MDR Life NDR1 NDS Brocken Regional Switching the regional programme function on/offREG Regional programmes PTY NDR1 NDS REG-E TextInfo Switching the PTY menu on/offPTY PTY Menu News AffairsPTY Menu News Programme typeActivate Switching PTY on / Selecting the programme typeAffairs Enter Clear Exit Giving radio stations a nameBremen 1 Bremen Bremen 3 HR 3 NDR1 NDS Switching traffic announcement priority on/offTraffic message reception with RDS-EON Search ScanTA OFF Exit Switching the warning beep offAutomatic start of station search PTY Traffic MessageAdjusting the sound stage for traffic messages and TIM Adjusting the volume for traffic announcementsTreble Bass Fader Balance Exit TIM Active Traffic Memo TIMYour motor antenna may be damaged in a car wash Correcting the time Setting the exact timeHours Hours + MIN MIN + Exit Displaying the timeTimer Programming the TIM standby mode / TIM timesTimer Hours Hours + MIN TimerCUE Hours Hours + MIN MIN + TimerRecalling stored traffic messages Active Exit TIM NDRActive TIM standby mode while the radio is switched offSwitching the TIM standby mode on/off TIM Active TimerTIM Active TIM-FUNCTION Deactivated MIX CD Name Scan Repeat TPM TPM CLR Switching to the CD modeOperating the CD player Inserting a CDSelecting a track Ejecting a CDRepeat TPM TPM CLR MIXScan Repeat TPM TPM CLR MIX CD Name ScanTPM TPM CLR TPM Programmed MIX CD Name Scan Repeat Repeating a track RepeatMIX CD Name Scan RepeatTPM CLR TPM Track Clrd MIX CD Name Scan Repeat Deleting the TPM memory TPM CLRMIX CD Name Scan Repeat TPMClear Exit V a L D Giving CDs a name CDC NameDeleting the name of a CD CD Name Selecting the display mode TRACK/TIMEDisc Switching to the CD changer modeOperating a CD changer optional Disc EmptyDisplay header will indicate the current selection Selecting a CD and a trackScan Time Repeat TPM TPM CLR Scan TR MIX CDC Name MIX DiscRepeat Track MIX CDC Name Scan Time Repeat a CD or a track RepeatTPM TPM CLR TPM CLR TPM Track Clrd MIX CDC Name Scan Time Repeat TPM Programmed MIX CDC Name Scan Time Repeat TPM CLR DiscTPM CLR Prev CD Next CD Clear Exit TPM Disc Clrd MIX CDC Name Scan Time RepeatDeleting the TPM memory for all of the magazines L D Deleting the name of a CD CDC NamePrev Next CD Clear Exit L D MIX CDC Name Scan Track Repeat TPM TPM CLR Switching on AUX AUX modeTreble +5 Bass DNC Fader Balance Exit Loudness Loudness on Audio settingsBass, treble, balance, fader LoudnessDNC-ADJUST Stop Adjusting DNCFader Balance Exit Loudness Adjusting DNC sensitivityDNC-LEVEL MID Treble Bass DNCAUTO-EQ3 MAN-EQ Exit EQ OFF EQ EqualizerEqualizer Menu AUTO-EQ1 View EQ AUTO-EQ2Start Hi-fi calibration Hi-fi calibrationChecking/altering Hi-fi calibration Yesno View AUTO-EQ Front Left Next ExitCalling up the Hi-fi calibration SET AUTO-EQ Front LeftCalling up the manual equalizer setting Setting the equalizer manuallyCar radios have been pre-programmed at the factory Programming with DSCTable Size Angle MENU-OFFKC LED DSC-VARIOUS Menu Clock VOL FIX BeepLoudness Exit Scantime VOL FIX DSC-KEYCARD Learn KC Read KC ExitMuting the audio source while using the car phone Tuner SpecificationsCD player Bosch Gruppe Blaupunkt telephone hotline